Question about 2000 Ford Focus

1 Answer

Tranmission trying to install new tranmission, need help with lining up right

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

Hi is it mannuall or automatic if its mannual you will a clutch lining tool to line the clutch disc before tightening the pressure plate if its auto you need to put the toruqe converter into the gearboxes housing and align the converters forks into the gearboxes oil pump by gently turning the converter and pressing lightly you will feel the converter slotting in keep revolving the converter till its full in be carfull otherwise you will damage the gearbox seal or pump then fasten box to engine and through the starter opening line the flywheel retaining bolts with converter don,t tighten them up until you have all the bolts in

Posted on Oct 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace 2006 trailblazer tranmission lines


there are spring clips on the fittings that you can easily remove with a seal pick slide the old line out replace the clip and o-ring inside of fitting and push the new line in till it clicks

Aug 29, 2014 | 2006 Chevrolet Trailblazer

1 Answer

I have a 2001 chevy impala,went to the store when got back home tranmission fluid was leaking out all over the place tried to but the barely moves in drive or reverse just paid for a engine to be put in...


Is it coming from the lines that go into the radiator for the trans cooler? If so, that is something that had to be hooked up properly when the new engine was installed. You need to see where the leak is coming from, but that is my bet. Do not attempt to drive it low on trans fluid, if it is not trash now it will be if you do.

Dec 28, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

Cant find where speed sensor is located on tranmission to change it out for the new one i have already got


HI the speed sensor is located on the front of the transmission. You will need to remove the air cleaner houseing to get access. The sensor will be to the right and under the shift linkage. I hope this helps happy hunting.

Aug 25, 2010 | 1998 Dodge Caravan

2 Answers

Need to replace ac condensor on 1999 taurus how do you do it


If your AC system is empty...The condenser is in front of the radiator.
1. Use ramps or jacks or a lift to raise the car so you can work under it.
2. remove the splash guard under the radiator.
3. Remove the bolts holding the tranmission cooling lines. These also may also hold the bottom of the condenser on the AC line side. Move the cooling lines away from the AC lines.
4. Remove the nuts holding the AC lines to the condenser. You may have to hold the fittings with a vise wrench to prevent bending the pipes.
5. Remove the other lower condenser bolt and use the access holes to remove the top bolts holding the condenser.
6. Lower the condenser out.
Reverse procedure to install the new condenser.

If you have the correct tools, this is a fairly easy job.

May 28, 2010 | 1999 Ford Taurus

1 Answer

Need to know where the vacuum lines for the 4l60e tranmission go in a 93 S15 gmc Jimmy


94 chev truck 4x4 350 put new injectors in now it idles to fast what to do (trottle body)

Feb 07, 2010 | 1993 GMC Jimmy

1 Answer

Have a 1992 plymoth voyger.It keeps losing tranmiss flued.have changed gasget and filter it still likes bad tranney work right when you put 2qt in but that is gone in about 5 miles what should i try now


check the lines going from tranny to radiator, make sure hose clamps are tight, or it could be your main seal, which you would have to take the tranny out for

Dec 04, 2009 | 1992 Plymouth Voyager

1 Answer

1998 dodge avenger tranmission control solenoid


Below the link for Chrysler/Dodge auto-transmission manual
http://www.scribd.com/doc/7095618/545rfe-Transmission-Manual

Solenoid mounts outside the transmission, so you do not need to remove the transmission to install. It should be located between fuse box and air filter housing on the top of transaxle case and right next to transmission controle module.
I hope his step by step procedure will work for you. It is not hard at all to replace the solenoid. There are three 10mm bolts. You will also need to remove the input speed sensor. One thing to look out for is not bending the gasket when installing the new solenoid:
  1. Disconnect battery negative cable.
  2. Remove air cleaner assembly.
  3. Remove electrical connectors for transmission control module (please refer the manual I send you and autozone.com website).
  4. Remove the Transmission Control Module
  5. Disconnect and remove the input speed sensor
  6. Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
  7. Disconnect the solenoid/pressure switch assembly connector.
  8. Remove the three solenoid/pressure switch assembly-to-transaxle case bolts
  9. Remove solenoid/pressure switch assembly and gasket

Keep everything clean to prevent foreign materials to go inside
  1. Install solenoid/pressure switch assembly to case using a new gasket
  2. Install bolts and torque to 13 N·m (110 in. lbs.)
  3. Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
  4. Uncap and install transmission oil cooler lines.
  5. Install input speed sensor and torque to 27 N·m (20 ft. lbs.)
  6. Install Transmission Control Module
  7. Install air cleaner assembly.
  8. Connect battery negative cable.

P.s. 1. You can fine some clips on YouTube.com at least for similar cars
2. Also at Autozone.com you can find the component location for your car and repair guide
3. Also there is a link for Mitchel1 online manual useb by US mechanic 1 week subscribtion is
11.99 , 1 month 16.99
http://www.2carpros.com/kpages/auto_repair_manuals.htm
Let me know if you need more info
Good Luck and happy fixing

Jan 22, 2009 | 1998 Dodge Avenger

1 Answer

Gmc 2500 tranmission


1993 gmc 2500 transmission interchange what years????
google transmission identification

thats the first step i thats how i found mine i have a 1993 gmc c2500 extended cab and here's the options TH700R4 ----4L60---- OR A 4L60E SO GOOD LUCK im trying to find out what years interchage

i heard if u have a 4.3L its 83-97 or 350 is 81-96

Oct 20, 2008 | 1993 GMC Sierra C2500

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...