Question about 2000 Oldsmobile Intrigue

2 Answers

Surpentin belt I took the surpintin belt off to put the water pump on and now I can't remember how to put it back on. Can any one help me it is a 99 Intrigue.

Posted by on



2 Answers

I just did one of these. No picture, but I can give you the routing.

Start at the TOP of the power steering pulley to
TOP of alternator pulley.
BOTTOM of alternator pulley to
TOP of idler pulley.
BOTTOM of idler pulley to
TOP of A/C compressor pulley.
BOTTOM of A/C compressor pulley to
BOTTOM of crankshaft pulley.
TOP of crankshaft pulley to
BOTTOM of water pump pulley.
TOP of water pump pulley to
BOTTOM of tensioner pulley.
TOP of tensioner pulley to
TOP of power steering pulley.

Have at it !!

Posted on Oct 15, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

If you have a car quest their they can show you or print a belt routing pic

Posted on Oct 13, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 vw jetta 2.0 4 cyl auto changed water pump timing belt driven put back together ran rough like out of time. put cam and crank at tdc per markings. engine rotates when key turned but dont start. just...

Did you remember to reconnect your Cam Position Sensor after putting it all back together? One tooth off shouldn't have bent a valve (but pressure checking cylinder will answer that). Did you check TDC once the belt is tight?

Aug 06, 2013 | 1999 Volkswagen Jetta

1 Answer

99 olds intrigue blows out clod air nd has leak in water pump

The water pump has to be replaced.Also inspect timing chain.Many a times while replacing water pump timing chain also gets misaligned.
Also loose overstretched timing chain causes water pump issues:-----

For complete water pump replacing procedure, step by step, there are few help links.I suggest you to refer the help links.


Click the link below:-----

Water pump replacing procedure for all vehicles?




How to route Water Pump Belt for 1992 Oldsmobile Cutlass Ciera?


How to replace Water Pump on Acura Car models?


How to Remove Water Pump on Toyota Previa?


Where is Water Pump located on Toyota Corolla?


These will help.


Dec 06, 2012 | Cars & Trucks

1 Answer

99 amigo Timing???????

you should not change the belt maybe now its not in the same position and that's a big problem

Mar 13, 2012 | 1998 Isuzu Amigo

1 Answer

How to remove water pump on a 98 oldsmobile intrigue

It is very easy! Take off belt by putting a wrench or socket on tensioner pully and rotating it. belt will come right off. You will have to drain coolant. then take out all of the bolts holding the water pump on. you will have to remove the power sterring pump to get to the very back bolt. Make sure you clean old gasket off of the motor and install new gasket with sealer. reassemble in reverse order.
On '98s at least there is an access hole in the p/s pulley that gives you access to that last bolt
I found no access hole except through the power steering which was easier to remove than the PS pully that a pully remover does not have sufficient room. Two bolts top and bottom through the access holes for the PS pump and it is out of the way of the last water pump bolt.

Dec 07, 2011 | 1998 Oldsmobile Intrigue

1 Answer

99 olds intrigue power steering belt very hot, I just replaced the power steering pump, it's makes a clicking sound and is getting very hot, sounds like it could be the steering colume.

remove the drive belt and check each pulley by hand for drag, or noise. Usually noises from the serpentine belt area are from the tensioner pulley, but since you installed a new PS pump I'd pay particular attention to that-also, watch the belt and pulleys for any 'wobble' too.

Apr 12, 2011 | 1999 Oldsmobile Intrigue

1 Answer

My power steering is gone? aslo I have replaced my thermostat and my water pump but my car still overheats when i am idling at a red light what else could be wrong?

check the fan belt on the water pump and on the steering pump
for heat see if your radiator fan runs when the car is heating up

you must have missed out the belts you took out while working on the water pump see manual for all the belts your car engine has and if they are there you did not tighten them properly

Feb 03, 2011 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides