Question about 1992 Ford Escort 4 Door

1 Answer

Locks wont stop

Hiya gang. my 1992 escort doors wont stop locking and unlocking an constant cycle until battery is flat, any clues?, to be fair the problem started after wash and polish last week and i just thought water had entered alarm module, but with alarm disconnected problem still occurs,im having to diconnect battery but that leaves the car unalarmed(i know it wont start with lead off but it can still get broken in to)please help. thanks
harriexr

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi again kids
i actually resolved this problem the long and silly way round??? because my alarm and immob are linked (separates but connectable) i believed that alarm unit was ok as still functioning, so marked and snipped immob wiring. wrong wrong wrong. i re joined each wire one by one to see if any thing changed with fault. it didnt have any effect, so back to wiring on alarm module, and after removing security screws, i emptied the water that had seeped into alarm wiring after washing car the week before, and a good hour drying out on raditor and it now works like a dream again, but i still have the problem of doors not locking automatically when alarm armed, though to be honest this fault started before the one i wrote to you about?
in essence im a big baffoon and have resealed alarm wire entry point as silicone had gone south a long time ago, allowing water to enter.
thanks anyway
regards
harrie the hose man

Posted on Oct 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do the car locks keep locking and unlocking on my Chevrolet lumina it's a 1992 year


you have a faulty door latch switch. it does not know that the door has locked check your door functions manually that will give you a clue which side

Oct 02, 2016 | 1992 Chevrolet Lumina

1 Answer

Can the immobilizer or central locking be switched off in a Nissan Almeria 2001 car?


you can remove the central locking fuse , this will stop the lock/unlock constantly , the problem is usually with the drivers door lock mechanism , that is perhaps why you cant lock/unlock with the key, lock from inside vehicle and get out passenger side, that lock should work with the key until you get the lock changed on drivers door

Jun 11, 2015 | Nissan Almera Cars & Trucks

1 Answer

My keyless entrey will not work has new battery?


Hi, please try reprogramming the fob using these procedures, and thankd for using FixYa:
Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jan 14, 2011 | 2003 GMC Sierra 1500

1 Answer

1999 Chevy silverado z71trying to program a new key fob


Use this procedure for New Body Style.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).




Apr 29, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I changed batteries in my 2003 GMC Sierra key fob


1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Mar 06, 2010 | 2003 GMC Sierra 1500

1 Answer

Need to re-program 2000 Chev.C3500 key fob need help


1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jun 09, 2009 | 1999 Chevrolet Tahoe

1 Answer

My remote does not lock or unlock my doors


You need to get an expert to reprogramme the security lock for you.

Good luck.

Rate this please.

Apr 25, 2009 | 2004 Toyota Tundra

1 Answer

My door locks wont stop locking and unlocking


You have a bad door switch, which is sticking. Try to clean it with contact cleaner or WD-40.

Dec 03, 2008 | 1992 Buick Regal

1 Answer

Door locks lock and unlock permanently


had this before but with a variety of faults ..boy racer alarm .take it off and invest in a decent steering wheel cover/lock ,fault in lock itself on drivers side as its used the most till i done one with the passenger side lock ,now that throw me .try throwing the boy racer sunday driver alarm away

Oct 12, 2008 | 1992 Ford Escort 4 Door

Not finding what you are looking for?
1992 Ford Escort 4 Door Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...