Question about 1987 Jeep Cherokee

1 Answer

How do i change a clutch in a 1987 jeep cherokee ?? all i really wish for is a brief explanation or a couple a pictures. i know how to change a manual transmission and i am wondering if there is any way to change it with out pulling the trany??

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

The transmission does have to come out along with the t-case.
There really is no short cut. The tranny has to come out to get to the pressure plate and clutch disk.
Make sure you do a complete job and replace the throughtout bearing also.

Posted on Oct 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

1 Answer

How to replace the heater cord on a 1999 jeep Cherokee?


You must remove the instrument panel and the A/C-heater housing to replace a heater core on a Jeep Cherokee.

I would be happy to provide complete instructions as well as diagrams if yu would like to take tis project on yourself.

Just click on my profile picture below and go to my FixYa profile page. Click the tab that says "Pro Services". When the page opens up, click any of the services listed. (It doesn't really matter which one - they will ALL connect you with me) Sign up for Email support. Be sure to include the Year, Make, Model, Engine Size, and a brief description of what we are trying to fix in your message (just so I don't mix you up with someone else). Youi can also do this by clicking any of my ads that you may see on FixYa.

Be sure to mention WHICH 1999 Cherokee you have...Cherokee Laredo, Grand Cherokee, Grand Cherokee Limited, etc. I would also need to know if you have MANUAL heating and air conditioning or if your vehicle is equipped with AUTOMATIC climate control.

Nov 13, 2011 | 1999 Jeep Cherokee

1 Answer

Smoke and smell of a "burning clutch" when the


ask a mechanic to have a look because without seeing it ,i couldnt really say

Jul 24, 2010 | 2000 Jeep Grand Cherokee

1 Answer

I have a few hydralic lines come off and a vaccume hose thats green that I dont know where they go.Its all connected to the clutch or master cylider.can I get apicture or diagram


give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by you local library and pickup a Haynes auto repair manual for your jeep and you can also stop by your jeep dealership in the parts department and they can print you off pictures and diagrams wish you the best of luck Michigan Man.

Nov 26, 2009 | 1989 Jeep Cherokee

2 Answers

Heat/AC Blower fan speed only works on High


hello, this sounds like a bad blower motor resistor!! its cheap and easy to change..if you need more info on locations let me know,, good luck.....marty

May 27, 2009 | 2005 Jeep Grand Cherokee

1 Answer

1987 Jeep Cherokee Chief Missing Clutch Mount Bolts...


dont remember fi they're metric but hardware store bolts will work there...remove another and bring it with you. (clutch hat uses grade 8 bolts that's why I asked.

May 16, 2009 | 1987 Jeep Cherokee

1 Answer

My jeep won't start (1987 Jeep Cherokee)


Your starter needs a "makeover". try to clean or change the brushes in the starter.

a cheap and simple solution, is to make the cables on the starter longer, and attach them to a button in you car. If you choose that solution, you just have to turn on the ignition, and then push the button you have connected the starter cables to.

Apr 11, 2009 | 1987 Jeep Cherokee

1 Answer

1987 Jeep Cherokee Chief power windows do not


jeep cherokee laredo 1987 problema que cuando suve una pendiente empiesa a vibrar.

Mar 15, 2009 | 1987 Jeep Cherokee

1 Answer

Jeep chreokee 1987


have you checked the relay? did they used to blink really fast before they went out?

Jul 30, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...