Question about Mazda Cars & Trucks

Open Question

Hi, Sorry Mazda demio 2002 was not on the drop down list. I was attempting to fit a band expander and gently tried prising the trim away that surrounds the headunit (As advised on an online forum!) I pulled but to no avail "It started to crease in the middle so I stopped immediately" must have loosened a connection because stereo is now dead! I am tech savvy so can fix it no worries but how on earth do you remove the surrounding trim to access headunit. Please Help. Steve.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Removing Car Stereo from ford Festiva (1998/9 model)

yes it was not avail. because its a aspire after 94. and you can pick up a ford stereo removal tool at local parts store, that is if you have 2 holes on both sides of the radio

Posted on Oct 05, 2008

Clanmartin
  • 2 Answers

SOURCE: Removing interior door trim '93 suzuki swift

Assume you have been able to remove window winder.
The surround of the the door handle (interior) is clip on at four points. Tabs are about an inch in from each corner and slide over a plastic nub to lock in place. . Start at top right corner. Get a small flat blade screwdriver with blade horizontal and gently - repeat gently, prise tab upwards while applying gentle pressure away from door and pushing slightly upwards. Tab should just slide off nub holing it in place. Do same for other side on top tab. Gently wriggle downwards so bottom tabs disengage. Installation is reverse.

Posted on Oct 12, 2008

  • 1 Answer

SOURCE: BMW DASHBOARD LIGHT 1998

Actually i think it means that your anti spin control is turned off. in my bmw the button for asc is located just in front of the gearstick. try pushing the button.

Posted on Dec 02, 2008

  • 548 Answers

SOURCE: How to remove door card on MX5 (2002)

Get a trim removal tool to use in pulling the door panel off. You will have to remove the screws under the arm rest as you find them. I would start at the bottom of the door and work up. You may want to assume that the work will progress better if the window is down before you begin. Mind the door handle as you remove things as the biggest complaint I've seen is that it fails to work right on the first try after getting things put back. Keep a magnet that has a telescoping arm handy to pick up things that fall to the bottom of the door. To remove window crank handles if you have them, put the trim tool behind the handle and engage the wire clip to remove it.

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: 2001 Jaguar S-type won't start

Check if your transmission really is in park. I once had the same problem and it was fixed by moving the stick in and out of the park stand for a couple of times. Then the red light illuminating the "P" came on and i could start again.

Has to do with the transmission cable that tends to get a bit loose.

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i tune Mazda Demio (2004 model) radio to Southern African frequencies?


fm frequencies are just that fm frequencies ( not japanese, chinese ,english or anything else
it is a range of frequencies in the fm band that local stations broadcast on
so all you have to do is to turn the tuner knob until you get 107 fm
so as you turn the knob you will loose 89 and it will go probably 90.5 , 100.20, 102.7 etc and if there is a station broadcasting that your radio will pick up it will come in and then fade out as you keep moving the knob
you may have to change the mode as there are fm 1 ,fm 2,fm 3 bands to get your fm 107 as it will depend on what megahertz 107 is operating on

Oct 05, 2015 | Mazda Cars & Trucks

2 Answers

Spark plug gap


Hi Dweckton, The plugs should be preset, but if not use a 1mm setting and that will get you running. Make sure that the electrode has not burned away if you're reusing the plugs. Regards John

Jun 07, 2012 | Mazda Demio Cars & Trucks

1 Answer

Is it timing chain or timing belt for mazda demio 2005 model


hi.
the demio has a timing belt.

on a 2005 car, unless you know it has been changed, it is probably due for changing just because it is 6 years old.

May 08, 2011 | Mazda MPV Cars & Trucks

1 Answer

How do you remove door panel off a freelander 51 plate. Winder making a grinding sound and sticking at times all help welcome


Yes they're easy to fit but there is a point to watch to avoid instant failure of the cable.

proceed as follows (5 door).......

remove the screw from behind the interior door handle and remove the trim
carefully prise the door pull trim off and remove the screws from behind
05 models onwards, remove the window switch assembly by pulling the whole black trim upwards
remove the plug behind the springy cup holder thing and remove the screw inside
finally remove 4 screws from the lower part of the door trim
carefully prise the door trim from the door and try to avoid breaking any clips

To get the reg out.......

Carefully remove the water shedder, this is easier said than done and really it should be relaced, if you have a new one, just rip it off.

Now, the point to watch, before removal, look at how the cables cross over and the cable nearest the outer side of the door crosses over the inner one and is clipped to the inner door skin, it MUST be refitted this way to keep the cables away from the window otherwise the window will catch the cables when wound down and break them, this is a common mistake so take your time and look before removing.

Next, Wind the window down (if you can) and loosen the 2 bolts that hold the window to the regulator, pull the window up and tape it to stop it dropping. If you cant wind the window down, cut the cables.

Remove all the 10mm bolts that hold the reg in and wiggle the reg out of the door.

Twist the new reg so the cables cross as previously mentioned, make sure they cross the right way, the cable with the pad should be nearest the inner door skin with the one without the pad crossing it on the outside.
Fit the reg in the door and tighten all the bolts, clip the non padded cable to the clip on the inner door skin.
refit the window.
Now, check the operation and make double sure the window doesn't catch on the cables, once your happy, fit the shedder and the door trim.

Jul 20, 2010 | 2002 Land Rover Freelander

1 Answer

How do you expand the FM band on a 2001 X-type Jaguar radio


FM band expanders are available on eBay. They will expand the FM band from 76Mhz - 90Mhz range to the 88Mhz - 108Mhz frequency range. Try eBay Australia, under "FM expander".

They fit very simply inline on your antenna wire (plug inline) and there's only one wire to connect to 12V + power supply... very easy to DIY.

Apr 30, 2010 | 2002 Jaguar X-Type

1 Answer

How to remove trim and panel to replace inside left door handle assembly for 1995 Jaguar XJ6?


There is a square plate, behind the chrome opener, prise this out and there is a screw behind it, there are screws in the bottom of the arm rest, the rest is just on plastic push fit rivits so the door card should just gently pull or prise free.

Jan 27, 2010 | 1995 Jaguar XJ6

1 Answer

I need to remove the drivers internal door panel


Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Feb 04, 2009 | 2001 Suzuki Swift

2 Answers

Removing interior door trim '93 suzuki swift


Assume you have been able to remove window winder.
The surround of the the door handle (interior) is clip on at four points. Tabs are about an inch in from each corner and slide over a plastic nub to lock in place. . Start at top right corner. Get a small flat blade screwdriver with blade horizontal and gently - repeat gently, prise tab upwards while applying gentle pressure away from door and pushing slightly upwards. Tab should just slide off nub holing it in place. Do same for other side on top tab. Gently wriggle downwards so bottom tabs disengage. Installation is reverse.

Sep 14, 2008 | 1993 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...