a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
put on lift and follow speedometer wire down back behind engine and just unscrew. The should stop it from working. You probably want to replace the speedometer by removing trim then unscrewing bolts/screws until you can remove the cluster panel. remember to remove all the stuff attached to back of it. then unbolt speedometer and install new one, but remember in some states that has to be done by a state certified person that would set it to the old amount of miles traveled. Someone had done it without setting it for current miles traveled and sold it to our Police Department and it was determined that the cars had 300,000 miles on it and not 5,000 so they were set to jail.
Remove the brake pads from the car and smear small amount of high melting point silicone grease e.g. Carlube, at the back of the brake pads. Be careful do not put on too much and never has it touch the pad material and the disc rotor. if you do, remove it with brake clearner immediately. The squeaks noise shall disappear if you fix it properly.
You have to remove the rear dash board. the covers don't come off. Remove the bottom seat first, then there will be 2 bolts to remove the back rest. Then you can access the speakers. To remove the bottom usually push it back and pull up where you sit you ****, on both sides.
your abs fault will be the right rear wheel speed sensor, it wont need replacing you just neet to remove the brake caliper and caliper frame, remove brake disc so you can get to the allen key bolt that holds the sensor in. remove the sensor and clean up where it sits and re-fit. as for the speedo fault i think the speedo drive is located on top of the diff. you may want to try removing the clocks, unpluging them and pluging them back in again
Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED
Safety Belt Bolt Bit
T77L-2100A NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.
Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear
Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
Remove rear seat cushion from vehicle.
Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear
60/40 Split Bench—Sedan Removal
NOTE: Safety belt bolts do not secure seat back to vehicle.
Remove rear seat cushion as described.
Fold down back seat and remove two bolts in the center of each seat back striker plates.
Remove two bolts from outboard rear seat back frame retaining brackets.
Lift seat back up and pull forward to remove from vehicle.
Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan
Remove rear seat. Refer to Section 01-10 .
Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
Pull lower quarter trim panel away from body.
Remove safety belt retaining bolt.
Feed safety belt through lower quarter trim panel.
Remove safety belt anchor plate-to-sill bolt from quarter panel.
Remove retractor anchor nut and retractor from rear quarter panel.
Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
Slide anchor plate end of safety belt through the openings in the quarter trim panel.
Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
Bolt (Part of 611B68)
Upper Rear Quarter Trim Panel
Retractor and Tongue
Rear Quarter Panel (Part of Body)
Lower Rear Quarter Trim Panel
Mounting Stud (Part of Body)
Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
To install, reverse Removal procedure.
Make sure the safety belt webbing is not twisted. If it is, remove the twist.
Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).