Question about 1989 Ford Festiva

1 Answer

Water pump I need a diagram for installing the water pump

Posted by on

  • 2 more comments 
  • I_SARGEANT Mar 06, 2009

    I had a radiator leak, and put rad filler which solved the problem. I now have no heat coming in the car

  • Anonymous Apr 05, 2009

    Yes Thank you for the instructions.

  • yadayada
    yadayada May 11, 2010

    It is in the Fortd factory repair manual, do you have one?

  • amysawyer32
    amysawyer32 Aug 07, 2013

    The heater core is clogged up



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I don't have pictures for you but here is instructions:
Drain all the coolant.
Jack up the car on the front passenger side.
Remove the passenger side wheel.
Put a jack under the oil pan.
Detach the engine mounts on the passenger side of the car.
Remove all external belts.
Remove the upper timing belt cover bolts
Lower the engine using the jack.
Remove the water pump pulley. (3 bolts)
Remove the upper timing belt cover.
Disconnect the coolant line running across the front of the engine from the water pump. (2 bolts on a flange)
Pull the timing belt.
Pull the water pump.
Installation is just reversed.

If you need images, go to your local library. I never bought a manual, where is the fun in that? LOL plus everything I need to know can be found on the internet.

Posted on Dec 20, 2008


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 173 Answers

SOURCE: i need a diagram for removal and installation of water pump

what engine is in the car??

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for a diagram of waterpump on a 1999 cadillac deville concours 4.6 liter


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the coolant.
  3. Remove or disconnect the following:

    Negative battery cable
Upper fill panel, if equipped
AIR injection control valve, if equipped
Air cleaner
Oil level indicator tube nut, if necessary
Water pump belt cover
Water pump drive beltLower radiator hose
Thermostat bypass hose from the coolant inlet housing
Water pump cover

Remove the water pump by rotating it clockwise using special Tool J 38816-1A (water pump remover/installer).
To install:
Install the water pump with a new O-ring, by turning it counterclockwise using the special tool, until it stops. Torque the water pump to 73 ft. lbs. (100 Nm).

Install or connect the following:

Water pump cover. Torque the bolts to 89 inch lbs. (10 Nm).
Lower radiator hose
Thermostat bypass hose to the coolant inlet housing
Water pump drive belt
Water pump belt cover
Oil level indicator tube nut, if necessary
Air cleaner
AIR injection control valve, if equipped
Upper fill panel, if equipped
Negative battery cable

  • Refill and bleed the cooling system.

  • Run the engine and check for leaks.
  • Oct 04, 2017 | Cadillac Cars & Trucks

    1 Answer

    I need to know where my water pump is in my 1994 Pontiac Grand Prix SE 3.1

    The included link shows where the water pump is located and how to change it. It is very accessible and easily changed.
    How to Install Water Pump for GM 3 1L V6 Engine Advance Auto Parts

    Aug 26, 2017 | Pontiac Cars & Trucks

    2 Answers

    Engine Diagrams

    Hello. Here a non-photo diagram. Hope this helps!!!

    The thermostat is located on the side of the water pump, the water pump is located just above the a/c compressor, the thermostat is fed coolant from the radiators lower radiator hose.
    Thermostat :
    1. drain coolant and tighten drain plug ( easier method : remove radiator cap, get big drain pan, place drain pan under lower radiator hose to radiator connection, remove clamp, slowly remove hose, allow coolant to drain into pan, now is a good time to remove radiator hose and clamp from thermostat housing )
    2. remove thermostat cover / cap ( easiest to get at this when front of car is supported by jack stands and right hand side lower cover is removed ).
    3. thermostat cap is held on by 3 bolts / remove thermostat.

    You will notice that the thermostat's air bleed hole is pointing up and lines up with notch in water pump housing,,

    ATTENTION :failure to install new thermostat in the correct location will cause engine to overheat.

    1. install new thermostat to water pump, make sure air bleed hole lines up with notch, install and tighten bolts, install a new lower radiator hose, fill cooling system.

    thermostat # 17670-77E00
    lower radiator hose #17854-65G20
    hose clamp #09401-36403
    upper radiator hose # 17852-65G20

    Suzuki factory manual

    Oct 21, 2013 | Cars & Trucks

    1 Answer


    1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
    2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
    3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.

    Jun 04, 2010 | 2001 Mazda MPV

    1 Answer

    2002 ford taurus wtaer pump

    Removal & Installation 3.0L (2V) To Remove:
    1. Drain the engine cooling system.
    2. Loosen the water pump pulley.
    3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
    4. Remove the accessory drive belt.
    5. Remove the generator.
    6. Remove the bolt and the accessory drive belt tensioner.
    7. Remove the nut, the bolt and the support bracket.
    8. Remove the bolts and the water pump pulley.
    9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
    10. Remove the bolts and the water pump, and clean the sealing surfaces
    To Install:
    1. Install the water pump. Tighten bolts in the sequence shown:
      1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
      2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
      3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
      4. Install the support bracket.
      5. Install the accessory drive shaft tensioner.
      6. Install the generator.
      7. Install the roll restrictor bracket, bolt and the nut.
      8. Install the water pump pulley.
      9. Install the accessory drive belt.
      10. Connect the battery ground cable.
      11. Fill the engine cooling system.

    Water pump bolt torque sequence (3.0L (2V) engine)

    Jul 04, 2009 | 2002 Ford Taurus

    1 Answer

    Need diagram to replace water pump

    1) Drain the radiator. 2) Loosen the 4 bolts on the water pump pulley. You will remove the pulley and install it on the new pump. Just loosen the bolts 1/4" turn with the belt still on, this will prevent the pulley from turning. 3) Remove serpentine belt. 4) Remove 4 bolts and the pulley and set aside. 5) Remove two power steering pump bolts (15mm). You must do this because one of the bolts for the water pump is behind the PS pulley, and you can�t remove it without moving the PS pump out of the way. The bolts on the PS pump are in the 12 o�clock and 6 o�clock position. There is a large access hole in the PS pump pulley. Just line it up, slip in a long socket and remove them. Let the PS pump rest on the oil filter housing. 6) Remove water pump. There are 4 large bolts (15mm) and 4 small bolts (3/8") on the water pump. After the bolts are all out, I placed a length of pipe on the water pump and gave it a couple taps with a hammer and it popped right off. 7) Remove old gasket. The tool of choice IMO is a razor blade like you�d use to remove a windshield inspection sticker. Be careful not to score the mating surface. Remove old gasket and dry off surface. 8) Seat the new gasket and water pump in place, install all the bolts. 9) Reinstall the PS pump and torque bolts. 10) Install pulley on water pump and torque. 11) Install serpentine belt. 12) Re-torque bolts on water pump pulley if needed

    Jun 29, 2009 | 2004 Pontiac Grand Prix

    2 Answers

    Water pump assembly and power steerin pump brackets

    need to know year? engine size?what accesories equipped? a/c power steer smog pump etc.

    Aug 26, 2008 | 1989 Dodge Ramcharger

    1 Answer

    Water pump

    you can buy some diagrams at . and yes all belts must go. goodluck

    Aug 01, 2008 | 1997 Dodge Intrepid

    Not finding what you are looking for?
    Cars & Trucks Logo

    342 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers


    Level 3 Expert

    5572 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides