Question about 1998 Isuzu Amigo

1 Answer

98 isuzu amigo starter removal

I am trying to pull the starter on my 98 amigo. This job realy sucks. It has the 2.2 engine in it. I was able to get the bottom bolt out and it appears that the top bolt was missing. The starter will not come out. Is there another bolt or bracket somewhere that I cannot see or feel.

Posted by on

  • korniye Feb 28, 2009

    I just cant take it out. Please help

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Could someone please answer this? I'm having the exact same problem.

Posted on Jul 07, 2010

  • dshoyt153 Oct 16, 2010

    this appears to be a common problem i am going to try this tommorrow, sounds exactly the same as my son described.?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the throttle positioning sensor on a 2000 Isuzu Amigo 3.2L V6 ??


hi, NAT.
the V6
the TPS is on the Throttle body.
what is a TB it that thing that sucks air in to engine to burn fuel.
that thing that the air cleaner connects to.

id you scan car first? if not that be first.

Sep 24, 2015 | 2000 Isuzu Amigo

1 Answer

What would make a Isuzu amigo to suck to much air, and idle high?


You need to check the coil packs, O2 or to lower the idle by loosening nut on back of jets and adjusting screw until idle is set as low as you want it but I would suggest 5-7 MPH. Tighten nut to lock in screw. This is a mechanic's cheater adjustment that takes less then 2 minutes to do.

May 22, 2014 | 1998 Isuzu Amigo

1 Answer

How do you convert an automatic transmision to a manual on a 99 amigo


I think you should have done more research before you started this project. The clutch wires you cant find may not exist on your Isuzu. Also the starter wont work without a signal from the clutch interlock switch. These probably also dont exist.

Sep 10, 2012 | 1998 Isuzu Amigo

1 Answer

Instructions to replace thermostat in 1999 isuzu amigo v6


if you have the 3.5 v6 izuzu engine the thermostat is a major job, requires removing upper intake ,because it is under not in front of like most thermostats.
about 3-4 hour job depending what kind of problems you run into.

Feb 16, 2012 | 1999 Isuzu Rodeo

1 Answer

How do you remove and replace a starter for a 1992 2.6L Isuzu Amigo?


1.The battery negative and more importantly positive cable must be disconnected.
2. There are 2 14mm bolts holding the starter in place, the upper bolt can be removed by leaning over into the engine compartment from under the hood with a socket and extension on a ratchet or a ratcheting wrench.
3. crawl under the front passenger wheel and remove the positive cable nut, remove positive cable from starter.
4. unclip the small ground wire attached to starter.
5. remove the lower starter bolt.
6. There is room on the bottom of the vehicle to wiggle the starter down to the floor and out from under the vehicle. There isn't enough room to get the starter out from the engine compartment up and out from under the hood.
7. installation of new starter is reverse of installation.

This procedure should work on any Isuzu Rodeo, Trooper, Amigo, or Honda Passport with a 2.6L 4 cylinder 4ZE1 engine

Nov 12, 2010 | 1992 Isuzu Amigo

2 Answers

1990 Isuzu amigo starter good battery good engine will not crank just one click any help


check you connection on battery and the wire that runs from battery to starter wiggle it while some one is trying to start the car.any luck let us know

Oct 26, 2010 | 1992 Isuzu Amigo

1 Answer

How do you read the oil stick on a 98 isuzu amigo


with the engine off pull the dip stick out wipe it off and put it back in the pull it back out if the oil is at the top hole it is good if it is at or below the bottom hole it is at least one quart low

Jan 13, 2010 | 1998 Isuzu Amigo

2 Answers

How to replace starter on 1998 isuzu amigo 2wd 4cyl


Removal
1. Battery ground cable.
2. Remove harness connectors
3. Remove bolts from starter.
Installation
1. Install starter assembly.
2. Install mounting bolts and tighten bolts to specified
torque
Torque: 25 N·m (18 lb ft)
3. Connect harness.
4. Reconnect the battery ground cable

Jul 02, 2009 | 1998 Isuzu Amigo

1 Answer

Trying to remove the starter on a 1999 isuzu amigo v6


not nesessary if you can acces the starter from the wheel well all yo have to do is remove the front wheel and yo can move the dust cover and the starter is right in fornt of you easy accesss!!!

Nov 14, 2008 | 1999 Isuzu Amigo

1 Answer

Code P1441 check engine light


Always check in at Planetisuzoo.com Hundreds of pros always ready.

Jun 26, 2008 | 1998 Isuzu Amigo

Not finding what you are looking for?
1998 Isuzu Amigo Logo

Related Topics:

829 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...