Question about 1986 Ford Bronco

1 Answer

Distributor my distributor in my 86 full size bronco is siezed in the and wont move therefore i cna tset my timing to allow it to run i need to get help asap ive had alot of suggestion just no one has told me they are 100% positive it will work

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 231 Answers

Okay tkis requires patience, first you need to get yourself some form of lubricant, the best one I have found is called ( move it ) diesel fuel is also very good too. where the distributor enters the block you want to apply this lubricant generously and keep doing so after letting the lubricant sit for awhile try twisting the distributor left and right. keep doing this and remember to be generous with the lubricant. and be patient as i've seen it take a couple ofdays to actually break free.

Posted on Oct 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Firing order diagram for an 86 ford bronco 2


Your local Auto Parts store can also confirm the firing order...be sure to find the correct #1 on your distributor cap...and rotate in the correct direction...Hope this helps.

Oct 29, 2011 | 1986 Ford Bronco II

1 Answer

Spark plug wiring


Ford Pick-ups and Broncos 1987-1996 Repair Guide
To avoid confusion, replace spark plug wires one at a time.



3f891cd.jpg

Fig. 1: 5.8L engine-nl-> Firing order: 1-3-7-2-6-5-4-8-nl-> Distributor rotation: Counterclockwise

4d7cb6a.jpg

Fig. 2: 4.9L engine-nl-> Firing order: 1-5-3-6-2-4-nl-> Distributor rotation: Clockwise

4670971.jpg

Fig. 3: 5.0L and 7.5L engines -nl-> Firing order: 1-5-4-2-6-3-7-8-nl-> Distributor rotation: Counterclockwise

e2e0c7b.jpg

Fig. 4: 6.9L and 7.3L Diesel engines-nl-> Injection order: 1-2-7-3-4-5-6-8


I hope help you (remember rated this help) Good luck.

Oct 05, 2009 | 1994 Ford Bronco

1 Answer

1987 FORD FULL SIZE BRONCO FUEL PROBLEM, SHUTS DOWN


The only way air can get in the fuel line is if you have a hole in it! Problem of course is were? I would run the fuel line from back to front and back again. Look for any wet spot that you can find. You may even have to drop the tank to ba able to look on top. I would suspect the problem is in the line before the high preasure pump, being as you are pulling air into the system. I have seen leaky lines allow air in, but not let fuel out.

Sep 12, 2009 | 1987 Ford Bronco

2 Answers

1987 ford bronco engine wont start


there is a two piece control module and pick up in distributor you could replace these or try a used distributor

Jul 23, 2009 | 1987 Ford Bronco

1 Answer

Wont start


if i drive my bronco to work shut it off it wont start sounds like it has a dead battery if i let it sit for an hour it will start back up can you tell me if you know what it is

Dec 15, 2008 | 1989 Ford Bronco

1 Answer

Car wont start


Its not to hard..part is about $ 50
  1. Remove the distributor cap from the distributor, and set it aside (spark plug wires still connected).
  2. Disconnect the harness connector.
  3. Remove the distributor.
  4. Remove the TFI module retaining screws.
WARNING Step 5 must be followed EXACTLY; failure to do so will result in damage to the distributor module connector pins.
  1. To disengage the TFI module's terminals from the distributor base connector, pull the right side of the module down the distributor mounting flange and then back up. Carefully pull the module toward the flange and away from the distributor.
  2. Coat the TFI module baseplate with a thin layer of silicone grease (FD7AZ-19A331-A or its equivalent).
  3. Place the TFI module on the distributor base mounting flange. Position the module assembly toward the distributor bowl and carefully engage the distributor connector pins. Install and torque the two TFI module retaining screws to 9-16 inch lbs.
  4. Install the distributor assembly.
  5. Install the distributor cap and check the engine timing.

Dec 10, 2008 | 1995 Ford Bronco

2 Answers

Bronco Wont Start (help please)


Check for timing gear problems. They have plastic teeth on the cam shaft gear which will shatter causing it to jump time.

Aug 03, 2008 | 1981 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...