Question about 1999 Chevrolet Blazer

1 Answer

Emission Code (Gas Cap) Could it be Pressure relief hose on the gas tank also?

Keeps setting The service light Coyld it also be the hose on the tank? Or just the gas cap.

Posted by on

  • Anonymous Mar 12, 2014

    gas cap and emissions light

  • Anonymous Mar 31, 2014

    emissions control light off

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 39 Answers

Yes it can be any part of the fuel system that is allowing air to escape, a way to find a air leak is to apply shop air to the fill neck while a helper listens under the car for air escaping, please be careful because gas can be pushed out with the air

Posted on Oct 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Gas cap indicaytor light came on. Changed cap and made sure it was tight but indicator light still comes on


The gas cap light is a generic light that indicates an emission problem. Usually a vacuum/pressure leak within the system. The gas cap is usually the first thing to check, however may not be the problem. There are numerous sensors and lines that control the vacuum/pressure/ of the fuel vapors and one of these is loose/disconnected/defective causing this light to come on. I would recommend inspecting hoses under the hood for any that may be loose/disconnected. You may also require a scan test to view sensor data to isolate the source of the light

Dec 29, 2015 | 2008 Chrysler Sebring

2 Answers

I would like to know what the code PO455 on a 2007 Mitsubishi Endeavor means.


Possible causes
- Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
help.jpg What does this mean? Tech notes
The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.
help.jpg What does this mean? When is the code detected?
Evaporative Emission System (EVAP) control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P0455 Mitsubishi Description
This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.
The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Read more: http://engine-codes.com/p0455_mitsubishi.html#ixzz3NlVyARyX

3022.gif

Dec 30, 2014 | Cars & Trucks

2 Answers

Fuel tank pressure relief valve


You have some otyher issue here besides the pressure problem.

Jun 22, 2013 | 1995 Geo Prizm

3 Answers

I have honda odyssey and the service engin coms on and the cod is p1456 so ineed to figur out thanks.


This probably means:
  • P1456: Evaporative Emission Control System Leak Detected (Fuel Tank System)
  • Usually this is because your gas cap was not fully tightened. Be sure to turn it until you hear a click.
  • After you tighten the cap, it might take a couple days of driving before the light goes-out.
  • Be careful to tighten your gas cap regularly, because otherwise it puts a heavy strain on your emission system.
-

Mar 03, 2011 | 2000 Honda Odyssey

3 Answers

P0456 error code on a 2003 Mits. Galant


P0456 = "Evaporative emission (EVAP) control system leak detected (very small leak)."

Feb 25, 2011 | Mitsubishi Galant Cars & Trucks

2 Answers

No pressure in gas tank when the cap is opened.


I am not sure I understan tghe question. You should not have a lot of pressure in the tank. There are hoses that capture any vapors that are in the tank and eleviate pressure build up.
Most often I have found the engine light on because of gas tank vent, such as loose
or bad gas cap or the vent valve stuck open. The computer does a cycle ever so often
and maintains the vent pressure build up in the gas tank and vapor canister, and if the purge valve sticks open the computer gives a check engine light and code as the pressure is not in the vapor storage tank when called for.
If your worried about no pressure at all then I would change the gas cap and see if this helps

Feb 03, 2011 | 2000 Nissan Quest

4 Answers

The code is p0442 what dose that mean and what part do i need


this is a small leak in the evaporative emission control system.Most common cause is a loose or faulty gas cap but not always, Sometimes the check valve in the gas cap doesn't seat properly allowing the gas tank pressure to bleed down. The EVAP system needs to see a positive pressure in the tank.

Jun 05, 2010 | 2004 Chevrolet TrailBlazer

3 Answers

2000 cavalier check engine light code po440


P0440 - Evaporative Emission (EVAP) System


evaporative emission (EVAP) system has a large leak.
Check the gas cap or vent valve. these are the most common problems.


The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the Fuel tank pressure sensor (FTP). When the sensor indicates a small leak in the EVAP system, this code is set.


Here are some additional causes.

* A small leak in any of the EVAP hoses or fuel tank hoses
* A small leak in the purge valve or vent valve
* The EVAP Canister may be leaking

Jun 06, 2009 | 2003 Chevrolet Cavalier

2 Answers

Error code p0442


EVAP Emission Control System - Small Leak Detected (1.0 mm). This code can be set when 1. fuel filler cap is not completely tight, 2. when various hoses get punctured or the canister close valve does not seal completely, 3. there is an actual leak in the charcoal canister, fuel tank, or other EVAP system component, 4. if any one of these components are malfunction (a), fuel tank pressure sensor, (b) purge control solenoid valve, (c) canister close valve, or (d) fuel cap. An engine vacuum leak would not set this code.
Solution: Take the vehicle to a Hyundai Dealership for proper diagnosis/repair.

May 23, 2009 | 2001 Hyundai Santa Fe

2 Answers

01 sonata gls v6...code po455, po442. what are these and how can I pass emissions test in arizona


If you have an EVAP leak, you will get the following codes:

1. P0442 evap emission control system leak (small).
2. P0455 evap emission control system leak (large).

If these codes come up, you need to trace the leak. The most common place for the systems to leak besides the gas cap is at the service port under the hood, the hoses at the purge solenoid, and the hoses around the fuel tank. Check all your EVAP hoses from under the hood , all the way back to the gas tank. You can repair a split hose easily. Buy some 14.5mm EVAP hose at the auto parts store. Just cut the split or cracked section out and attach the new hose.

I can only say that u must fix the code issue and light to pass state emission test, if u reset the light they will know, the system will tell the tester that the system is not ready, this will cause a fail.

Mar 16, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...