Question about 1996 Subaru Legacy

1 Answer

No running lights

All other lights work...no running lights,fuses,relay and switch are good..Any help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

How do you know the switch is good?

The switch is 99% of the time the problem asociated with no running lights.

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Headlights won't work on my 04 Aztek, checked fuses, relays and bulbs. All are good, only the fog lights and daytime running lights will come on.


as you checked already fuses, relays and bulbs there must be something wrong with the light switch in the dashboard.
- either a loose connector or worn out contacts. first remove the switch and spray some WD-40 or similar contact spray into the connector from behind - if that does not help you have to replace the light switch with a new one...
25403468-uvoyhq0tcvcwuiaxihs2uqxu-1-0.jpg

25403468-uvoyhq0tcvcwuiaxihs2uqxu-1-2.jpg

Feb 06, 2015 | 2004 Pontiac Aztek

1 Answer

FORD 2001 CV - Headlights and running lights off, instrument cluster lights off, dome light off, rear window defogger off, turn signals not working. Check all mini fuses under dash OK, maxi and mini fuses...


Your owners manual will show you the location of the relay, for the lights, swap the lights relay with another on. Also, if the light switch is working, and the fuse is good, you will be able to hear the relay click. Have a helper run the light switch while you listen for it to click.

Dec 23, 2014 | Cars & Trucks

1 Answer

Running headlights not working need solution or is there a switch for lights


Head light have two relays.one for daytime and one for normal night. the daytime switching the light to serial circuit and if one bulb is out down both Leigh quit working. Inspect your light high and low beam for normal operation . Inspect your fuses . Swap the daytime relay with identical one.and under the dash is module for daytime running light. inspect the red/black wire for ground from light switch and light blue/ yellow for power from 15A ECU-B fuse
good luck

Jun 05, 2014 | 1994 Toyota Camry

1 Answer

Tail lights and dash lights is no working


did you check them in the dark to see if , not just dim?
what sub model, EX, or LX? the LX is very different.
the car has 2 fuse boxes. did you know that, most cars do.
the fuse is called fuse #10 (fuse 10 runs hazards too, are haz dead?)
box one in cab, and 2 in engine bay.
the HAZ fuse is marked, HAZ

park/dash dim all dead, this is the largest path in car, over 20 lamps on most cars. (lots of places to mess up)
all are dead, all parks, front , rear, side and cab (dim) dead??????
even the license plate lamp>>>> details?,,,,, help, im blind..
here ill login to alldata.com for you, so can you at anytime.

ok this car can have a tail light relay. the LX dont have one.
the combo switch (1st click ) turns on park(tails)
and the relay energizes and runs all the park lamps.
but not on the LX, the LX is switch direct drive to all parks.
so?????

found this with google. NON LX !!!

Fuse #10 (15A) Audio unit, pocket light, clock, climate control, cruise switch light, gauge assembly, hazard switch light, heater control panel, interior lights switch light, driver's multiplex control unit, power sliding doors switch light, rear A/C switch light, taillight relay TCS swtich light.





Dec 30, 2013 | 1999 Honda Odyssey

1 Answer

My amber runing lights and tail lights dont work but hazards and brakes work . just no running lights at all? is there a relay from my switch on the colum to the lights that im missing. All fuses are good


There very well may be one in the fuse/relay center either under the hood or inside the car near the floor or glove box. A relay may make a click sound when the switch is turned to the first position, but not make the lights come on, due to burned contacts inside the relay. Find another one that is the same type and switch it and see if they come on now. If they do, change the relay and your done. Otherwise you may have a poor light switch on the column.

Jan 20, 2011 | 1997 Honda Civic

1 Answer

My headlight , running lights and dash lights don't work , my dome light , warning lights , signal,and hazard lights all work. all fuses are good ,checked them twice..


Hello,

Once you have checked the fuses and they all seem to be intact, then you need to check the relay switch of the car. Most of the times it develops faults hereby resulting in those lights not working.so run a check on the relay switch because the lights cannot all stop working at the same time without it being a fault from a component that controls them.

Hope this helps.
Take care and good luck

Jan 08, 2011 | Dodge Spirit Cars & Trucks

2 Answers

High beams work but not the low beam lights


check relay!!!!!!!!!!!!!under hood in relay//fuse cluster,cheers

Dec 23, 2009 | 2006 Dodge Ram 2500

2 Answers

Dash lights and parkings lights out. Everything else works. Fuse is good. Circuit relay makes noise when parking light switch is turned on. Is it a short or switch or something else?


i would say the relay was working it is supposed to clunk when something is turned on check bulbs or maybe light switch hope this helps regards Jim

Apr 04, 2009 | 1993 Ford Probe

Not finding what you are looking for?
1996 Subaru Legacy Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...