Question about 1985 Mercedes-Benz 190

1 Answer

Rear Pad Replacement

I have a 1985 Mercedes 190E and i have done work on cars before i went to go replace the rear pads today and found 2 pins holding the rear pads in place i could not find a way to get the pins out i have sprayed them with wd40 and nothing any advice on how to get the pins out to replace pads

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello! You need to take a hammer and a punch and knock the pins out, they will go back in easy but that is how you remove them.

Posted on Oct 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the rear brake disc on a 1996 Mercedes C280


EASY PUSH THE PIN OUT THAT HOLDS PADS SLIDE OLD PADS OUT .PRESS THE CALIPER BACK IN WITH PRY TOOL INSTALL NEW PADS ,SLIDE PIN BACK IN ,DONE TAKES 5 MIN TO CHANGE PAD,PIN IS ABOUT 2 IN LONG 3/16 IN DIA.
E

Jul 07, 2014 | 1998 Mercedes-Benz C-Class

1 Answer

Rear rotor replacement for a 1985 mercadies benz 500 sel


YOU NEED TO SAFELY RAISE SUPPORT REAR OF VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. YOU NEED TO SIPHON JUST A LITTLE BRAKE FLUID OUT OF THE MASTERCYLINDER.BECAUSE YOU NEED TO USE LARGE C - CLAMP TO COMPRESS FORCE PISTONS BACK IN THE CALIPER BORES USING LARGE C - CLAMP DOING THIS WILL ALLOW YOU ENOUGH ROOM INSTALL NEW REAR BRAKE PADS.TO REMOVE REAR PADS ONCE YOU COMPRESS PISTON BACK IN THE CYLINDER BORE. YOU CAN TO REMOVE REAR BRAKE PADS BY REMOVING RETAINING PINS IF EQUIPPED OR BRAKE PADS HELD IN PLACE BY RETAINING BOLTS.ONCE YOU HAVE NEW REAR BRAKE PADS INSTALLED.PLACE MASTERCYLINDER COVER BACK ON TOP OF MASTERCYLINDER THEN PUMP BRAKE PEDAL TO SEAT NEW REAR BRAKE PADS AGAINST THE ROTOR UNTIL BRAKE PEDAL FEEL FIRM AND SOLID.THEN RECHECK BRAKE FLUID LEVEL IN BRAKE MASTERCYLINDER ADD LITTLE MORE FLUID IF NEED DONT OVER FILL MASTERCYLINDER.

Sep 11, 2011 | Mercedes-Benz 500-Class Cars & Trucks

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

1 Answer

Brake pad replacement on 2005 Acura MDX


1. torque on the slide pins is about 25 to 30 ft lbs.
2. torque on caliper bracket to knuckle is 80 to 100 ft lbs
3. get the best pad you can get ,its an Acura . I recommend Bendix import quiet ceramic pads.
4. ceramic = less noise/dust less stopping power
metalics= better stopping power/noisey lots of dust

Apr 28, 2009 | 2005 Acura MDX

1 Answer

Rear brakes


NEED A 17MM SOCKET TO REMOVE THE REAR TIRES, THEN THERE IS A PIN THAT HOLD THE TOP OF THE PADS IN. YOU MUST REMOVE THAT PIN WITH A TYPE OF PUNCH AND USE A HAMMER . PUNCH IT OUT THEN REMOVE ONE PAD, PUSH THE PISTON IN THEN THE OTHER PAD. PUT THE PIN BACK IN PLACE, DO THE SAME TO THE OTHER SIDE

Mar 24, 2009 | 2003 Mercedes-Benz C-Class

3 Answers

Rear pad replacement on a Jaguar S-Type


Well,

I fill you in what I learned today. I have a 2005 S-Type Jaguar and the dealer sayed it needed new pads in the rear. They wanted $300 just for the pads and another $150 or so to install. That $450 bucks to replace the brake pads only on the rear of the car. And of course, the extended warranty doesn't cover this, so I said no thanks. I found the best brake pads from Napa for $52. I purchased them through my brothers shop- saved a little. I done lots of brake pad replacements over the years, but not on a new car like the Jaguar. Well they are a little different and the frist one took me awhile . Here is the trick. 1) MAke sure the parking brake is off and you do this by starting the car, stepping on the normal brake and then pushing the parking break lever down while shutting off the car. 2) You then take the tire off, use jack stands to ensure safety.3) Take off brake callipers, 2 bolts and the brake pads should just fall off.4) take the anti-rattle plate off the old pads by prying it off carefully with a tiny screw driver- clean and then install on the new ones. 5) Here I release the the valve for the brake fluid. I did not want to damage the system if the fluid went back into the system when I retracted the calliper. You use some fluid, but you can add when finished. 6)You either need one of those brake calliper tools that you push the calliper in with and If you don't have the trick new one with the keys to turn the brake calliper cylinder, you can get by with the old version like I did and use a pair of channel locks to turn counter clockwise, while continuing to turn the tool. The cylinder needss pressure on it while you turn. This will put in in the proper place. 7) Ensure you have the slots up and down so that the pin in the pad fits up into the cylinder. you know this is correct when you have it perfect vertical and center within the calliper. Pay attention when taking off! 8) Set the brake pads in their proper place and then slide the calliper over them. IT should go over freely or else you need to turn more on the cylinder. 9) Tighten the bolts and replace the tire and you are done. Next side!
Hope this helps. -Dave @ dchristi@zianet.com

Nov 18, 2008 | 2001 Jaguar S-Type

1 Answer

REAR BRAKE PAD REPALCEMENT


Hello, When you are looking at the caliper, you should see two pins holding the pads in. Look for the holes or the ends of the pins and drive them toward the inside of the caliper until they come out. Then take a large screwdriver or large channel locks and pry the pads away from the rotor. Now you should be able to take the pads out. When installing the new pads, you will have to put the pins back from the back side until they are flush with the caliper. When finished, make sure you pump the brake pedal until it comes up to the normal level before trying to move the car.
I hope this helps.
CYA Gator241

Aug 22, 2008 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...