Question about Jeep Wrangler

1 Answer

Reset change oil display 2008 jeep wrangler - Wrangler Jeep Cars & Trucks

Posted by on

  • 1 more comment 
  • Anonymous Mar 29, 2009

    what kind of oil do I need to retop a 2000 Jeep Wrangler?

  • Anonymous Apr 22, 2009

    Tried did not work

  • Anonymous Mar 22, 2014

    reset oil change light


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three
times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Posted on Oct 09, 2008

3 Suggested Answers

  • 731 Answers

SOURCE: mechanic did not reset my

1. Turn the ignition switch to the ON position (Do not start the engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position

Posted on Jan 06, 2011

  • 6982 Answers

SOURCE: Help on changing oil pump 0n 1999 jeep wrangler

Pump is fairly simple...remove pan unbolt pump and reverse procedure. It is good to pre-lube pump and fill oil filter before starting engine. BUT: Keep in mind that a damaged pump is generally not the cause but the result of a failure elsewhere. Primary reason is rod or main bearing wear, resulting in debris scoring the pump gears and internal surfaces. Therefore, changing the pump will at best, slightly raise pressure only for a very short time. If after removing the pan, you find that the pump pickup is nearly blocked off by hard carbon deposits, you may have a chance of regaining pressure, providing bearings have not been damaged by low oil suppply caused by that restriction.

Posted on Jun 10, 2009

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Resetting the change oil light on 2008 jeep compass

turn key on til message appears,push gas pedal to floor 3 times (engine not running)

Nov 09, 2012 | 2008 Jeep Compass

1 Answer

2008 jeep grand cherokee reset oil change light

if it is the display on the console, select the change oil prompt, press and hold the select button for a few seconds. the display should read 'oil life reset 5000 mi'. if the display is above the rear veiw mirror near the map lights, select the oil life reset prompt, press and hold both the set, and select buttons at the same time. refer to owners manual for exact procedure if it still doesnt work

Feb 01, 2011 | 2008 Jeep Cherokee Grand

1 Answer

Mechanic did not reset my oil change indicator when had oil changed it still chimes and flashes change oil when i start my 2008 jeep wrangler how do i reset it

1. Turn the ignition switch to the ON position (Do not start the engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position

Jan 05, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

I have a 2008 Jeep Wrangler Unlimited, and bought it new. I perform regular oil changes, and drive very little. A few months after the last oil change I noticed the oil light come on very briefly, then...

You probably spun a bearing. My wifes 2000 ford mustang did the same thing she never checked the oil and she said the oil light would come on briefly and oil empty filled back and knocking during acceleration and idle tore apart motor and there were three spun bearings.

Sep 15, 2009 | Jeep Wrangler Cars & Trucks

1 Answer

2008 jeep wrangler how to reset service light on the dash

there are two ways to reset the light. you can use an obd2 scan tool to read and reset it or you can pull your battery cables off for a half hour and that will also reset it. just be forewarned if you have not fixed the problem that turned it on in the first place it will just come back on. if you have fixed the problem after 50 starts without seeing the issue again it will also clear itself.

May 19, 2009 | 2008 Jeep Wrangler

1 Answer

2008 jeep wrangler how do you reset the service light on the dash

turn jeep gas peddle quickly 3 times..wait 15 seconds...turn car on. if it doesnt work, adjust the speed of pressing gas peddle.

May 17, 2009 | 2008 Jeep Wrangler

1 Answer

2008 jeep, electrical problem - won't start

try removing the IOD fuse in the fuse block for a minute then reinstall it. will reset the computer

Jan 16, 2009 | 2008 Jeep Wrangler

1 Answer

Oil leaking from shock

I would not drive it like that. Have them come and get it. I used to work for Gabriel Shocks at the Manufacturing Plant in Oklahoma and can Tell you that you Could loose Control Driving it that way. Warranty will cover it.

Jan 04, 2009 | 2008 Jeep Wrangler

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

1,980 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

67800 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides