Question about 2005 Ford Freestar

1 Answer

Egr valve where is it located and what does it look like?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

The egr is located on the exaust side of the engine closest to the fire wall it will have a tube that is intergrated to the valve itself there will be a plug to it as well. the one tub will go to the intake manifold then to egr valve and there will be a tube to the exaust manifold the valve will be round in shape.. please rate this

Posted on Oct 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Erg flow insufficient


  • The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (tube), most likely carbon buildup
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vaccuum
It is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
  • Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
  • Clean out the EGR valve and/or tubing to remove deposits
  • Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
  • Replace the DPFE sensor (with a good quality / OEM one)
  • Replace the EGR valve
The EGR valve is located in the engine compartment. Its should look this

2_7_2012_10_25_48_pm.jpg

Feb 07, 2012 | 2000 Mercury Sable

1 Answer

Is there an EGR valve on 01 Jeep Grand Cherokee 4.7 L, and if so where?


The EGR Valve is located on the rear, driver's side of the engine. It's a failry easy job, and you should be able to this yourself.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head. An exhaust gas routing tube connects the EGR valve to the intake manifold.

2010-05-30_173844_1.gif
  • Remove electrical connector at top of EGR valve solenoid.
  • Remove tube mounting bolt at intake manifold.
  • Remove two bolts connecting EGR tube to valve assembly.
  • Remove gasket located between EGR tube flange and EGR valve assembly. 2010-05-30_173909_2.gif
  • Remove two EGR valve mounting bolts.
  • Separate valve assembly from engine.
  • Remove and discard metal gasket located between cylinder head and valve assembly.


Sep 30, 2011 | 2001 Jeep Cherokee

2 Answers

My car is a suzuki xl-7 2002. it's has a problem with an egr valve. How you can help,me please,and where is the egr valve is located.?


The EGR valve will be mounted on the intake manifold, and may have either wiring or a vacuum hose attached to it. Type 'EGR valve' into Google images, and you will see what it looks like.

Sep 25, 2010 | 2002 Suzuki XL-7

1 Answer

I cant locate the egr valve on a 1998 Dodge ram 1500 5.2 L


An EGR valve assembly located at the front of the intake manifold. The EGR valve is a poppet style valve (on/off only) and is controlled by an internal diaphragm.

af91f0c.jpg

Fig. EGR location and associated components-California diesel

Hope helps (remember to rate this and comment ).

Sep 14, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

Where is the egr valve on a 2005 dodge 1500 5.7L


The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.

2efe0f8.gif

Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

TY for using Fixya; remember rated this post.

Apr 14, 2010 | 2005 Dodge Ram 1500

1 Answer

WHERE DO I LOCATE THE EGR VALVE ON MY 2001 CHEVY IMPALA 3.8 V6


The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks

Feb 27, 2009 | 2001 Chevrolet Impala

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

2 Answers

EGR VALVE ON 96 FORD PROBE SE


If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Aug 24, 2008 | 1996 Ford Probe

Not finding what you are looking for?
2005 Ford Freestar Logo

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...