Question about 2007 Chevrolet Uplander LT Minivan

1 Answer

Can the buttons on the remote be canceled for the sliding doors?

I carry my remote on my key ring and sometimes when I enter my garage I find one of the sliding rear doors open. I think it is caused by my keys pressing against the button on the remote either when I move around to do a task or maybe when I put my hand in my pocket to get other keys etc. I thought there may be a way to keep the remote from unlocking those doors but I could not find anything in my vehicle owners manual.

Thanks
Chuck

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi,
I contacted the Cheverolet dealer where I purchased the vehicle: and there is no solution unless you switch the doors to a manual operation.
Regards
C Bouse

Posted on Oct 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 dodge caravan automatic sliding doors open when keys are in pocket


Keep the keys out of your pocket. Something is touching the open switch in your pocket.

Jun 13, 2012 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

How to program a garage door opener in a 2007 Acadia


Grab the remote for the garage door you want to program, then pick a button you want to match the door, next is turn key on push button on the truck and then button on the remote, hold both buttons until flashing red light turns green. you can do this with each button and each remote.

Mar 02, 2012 | 2007 GMC Acadia SLE

1 Answer

I cant get into my car at all none of the windows doors hood or trunk will open. what do i do


On your remote look closly there is a little sliding switch that releases door key thats hidden inside remote.Slide switch and pull key ring side and use that key to open doors or trunk.

Mar 13, 2011 | 2008 Dodge Charger

2 Answers

Doors lock and unlock when not even around car


try changing the batteries in the remote.....

Jun 07, 2010 | 2000 Nissan Xterra

2 Answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.


Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.

Mar 09, 2010 | 2002 BMW 5 Series

1 Answer

Programing garage door openers


Press the button on the garage door opener (red, green, or yellow) until the led starts to blink and within 10 seconds or so, ( I think it's actually 30 seconds) press the GDO control button on the remote and the opener should capture the signal and respond to it from then on. Any remotes that were set to control the opener will be wiped and the new one will be in control. There are instructions that came with the opener that show how to do this from the remote or the key-less entry. If you are talking about an in-car device then your vehicle manual may be needed too, but the main thing is to set the GDO to be looking for the code from the car remote and when you press the in-car remote the garage door should respond. If you have programmed a remote or key-less entry then it is about the same procedure.

Jun 12, 2009 | 2008 Subaru B9 Tribeca

2 Answers

Key fob does not unlock the doors


remove the keyring from the fob open it and replace the watch battery in it

May 25, 2009 | 2005 Chrysler Town & Country

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

2 Answers

Program my garage door opener


What the last guy post is correct, but you have to tel your car what kinda remote you have. Assuming you have homelink Which 95 percent of the cars do ill give you a very short version on how to do this. First thing you need to do is clear the code in your car from any other owners. Do do this turn your car's key to the on or acc non running position. Press and hold the first and last button. Untill the light reacts different ether starts flashing or flashes faster etc. Then you need to get one of your remotes. Press and hold the button you want to set in your car and press your remote button at the same time untill the light reacts diferent. Mind you hold your garage remote as close to your car remote as you can. Then finally Find your learn button on your garage door opener it's self it can be in the back or the front if its in the front you have to remove the cover press the button once DO NOT HOLD IT. then go to your car and press the button you set for about 2 seconds and repet 1-2 more times untill your garage door moves. Make sure nothing is in the way of the garage door. (I know that should go with out saying.)

Dec 29, 2008 | 2001 Chrysler Sebring

1 Answer

Programming the garage door opener


Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Jun 06, 2008 | 2003 Jaguar XJ-Series

Not finding what you are looking for?
2007 Chevrolet Uplander LT Minivan Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...