1999 dodge dakota p1762 code

there are about a dozen O2 sensor codes. Tell us which one you have

O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2) P0141 OBD II Trouble Code O2 Sensor Heater Circuit Malfunction Bank 1...

P0306 PONTIAC - Cylinder 6 Misfire Detected https://www.autocodes.com/p0306_pontiac.html

P0141 PONTIAC - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 2
P0141 Pontiac O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 2

P0442 FORD - Evaporative Emission System Leak Detected Small Leak

Possible causes- Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
P0136 - O2 Sensor Circuit Malfunction Bank 1 Sensor 2
Possible causes- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Rear Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

P0141 FORD - O2 Heater Circuit Bank 1 Sensor 2

Possible causes- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Engine Control Module (ECM)

Hi there:
Both codes refer at O2 sensor...


DTC P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141. See also: P0135 (Bank 1, Sensor 1).



You will likely notice poor fuel economy the illumination of the Check Engine Light.



A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element
Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.


Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors





DTC P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)
The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)



There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.


A code P0138 may mean that one or more of the following has happened:
Faulty O2 sensor
Short to battery voltage in O2 sensor signal circuit
High fuel pressure (not as likely)


Here are some potential solutions:
Replace O2 sensor
Repair short to battery voltage in o2 sensor signal circuit.


Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

P0141 is O2 Heater Circuit (Bank 1, Sensor 2) It will be the sensor AFTER the cat on the side that has #1 cylinder. On your car it's the PASSENGER side.

P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

there is a fuse for the o2 heaters if one of the sensors blew the fuse they will all be out

You said you changed the O2 sensors, which ones? I do believe that sensor 2 is the Catalyst efficiency monitor, it looks like an O2 but it's function is different. This sensor is behind the Catalytic converter, the O2 is in front. Bank one is the bank that # 1 cylinder is on, so the sensor that is defective is the 2nd sensor back on that sides exhaust pipe.

P0141 - Heated Oxygen Sensor (HO2S) Heater Performance Bank 1 Sensor 2

P0138 - Heated Oxygen Sensor (HO2S) Circuit High Voltage Bank 1 Sensor 2