Question about 1992 Ford Explorer

1 Answer

How does one get the lifters out

Does the head have to come off to replace the lifters

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 61,249 Answers

No, just pull the lower intake manifold off, they make a special tool that grips the inside of the lifters to remove them.

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the lifters in my 04 chevy cavalier 2.2 ecotec with out pulling the head


you dont have to remove the head but you do have to remove valve cover timing chain cover since you will be removing both cams to access the hydraulic lash adjusters {lifters}the link is not the 2.2 but shows what is entailed in removing the cams
Cylinder Head 101 Remove Cams Rockers Lifters

Jun 17, 2016 | 2004 Chevrolet Cavalier

1 Answer

2002 explorer 4.0L sohc: I've stripped driver side down to ticket arms and tip of lifters. Is there anyway to replace the lifters without removing the head?


I think they have a tool that you can slide the lifters out of the head without removing the head. I've never done this on this particular vehicle but I have on Ford V8 engines from the 70s without any problem. I'm pretty sure you don't need to remove the heads to replace the lifters.

Nov 18, 2015 | Cars & Trucks

2 Answers

No Start - Lanos 99 SOHC 1.395cc


Hi. I can give you a simple, but time consuming test to do to check your intermittent compression problem. New hydraulic lifters cause a lot of problems until its settled. Remove the camshafts and the hydraulic lifters. Take each hydraulic lifter and put it in a vice(becarefull not to damage them) and squeeze out all the oil in the lifters. Then put them back and replace camshaft and allign timing marks. Check compression ratio. What happens sometimes is that the oil pressure is too high(stuck oil pressure release valve or cold thick oil) and this causes the oil pressure to put so much pressure on the hydraulic lifters, that it slightly forces the valve open. That will cause your low compression as well as backfire through the intake.

Jan 14, 2014 | 1999 Daewoo Lanos

3 Answers

I have a loud ticking under my valve cover. 97 ford escort. I think its a loose valve but is it some thing i can fix. I know a little about cars. but not an expert


not a valve, but a lifter. I will paste procedure below. You judge if you can do it or not. Recommend you replace them all while you're in there. If you let this go, the lifter will wear out the camshaft. Lifters are $22 each, and you have 8 of them. You will also need a new valve cover gasket.
Please let me know if you have questions, and thanks for using FixYa.

2.0L Engine
SOHC engine
See Figures 6, 7, 8 and 9
  1. Disconnect the engine air cleaner-to-valve cover hose from the cover by compressing the hose clamp with pliers and sliding the clamp back, then separate the hose from the cover.
  2. Remove the spark plug wire separators from the valve cover and set the wire assemblies aside.
  3. Unfasten the three valve cover retaining bolts.
  4. Remove the valve cover and gasket from the cylinder head.
WARNING Do not use any abrasive grinding discs to remove gasket material. Use a plastic manual gasket scraper to remove the gasket residue. Be careful not to scratch or gouge the aluminum sealing surfaces when cleaning them.
  1. Remove the old gasket material from the cylinder head and valve cover mating surfaces.

jturcotte_163.jpg

Fig. Fig. 6: Remove the spark plug wire separators from the valve cover

jturcotte_164.jpg

Fig. Fig. 7: Compress the engine air cleaner-to-valve cover hose clamp with pliers, and slide the clamp back ...


jturcotte_165.jpg

Fig. Fig. 8: ... then disconnect the hose from the valve cover


jturcotte_166.jpg

Fig. Fig. 9: Unfasten the valve cover retainers and remove the valve cover-2.0L SOHC engine


If removing more than one valve lifter (tappet), mark the lifters and their locations as they must be installed in their original bores.

  1. Remove the rocker arm(s).
  2. Unfasten the lifter guide plate retainer.
  3. Remove the guide plate and the lifter.


To install:
  1. The oil feed hole in the lifter must face away from the oil feed hole in the cylinder head.
  2. Lubricate the lifter(s) with clean 5W-30 engine oil and install them in their original bores.

Make sure the lifter guide plate retainer tabs are towards the rear of the cylinder head, and the lifter guide plate tabs are towards the front of the cylinder head.
  1. Install the lifter guide plate and tighten the retainer.
  2. Install the rocker arms.
Do not use any sealer with a silicone type gasket.
  1. Install a new gasket and the valve cover.
  2. Install and tighten the valve cover retainers to 71-97 inch lbs. (8-11.5 Nm).
  3. Attach the spark plug wire separators to the cylinder head.
  4. Connect the engine air cleaner-to-valve cover hose and engage the hose clamp

Jan 19, 2011 | Ford Escort Cars & Trucks

1 Answer

Can you replace a lifter in a 454 chevy without removing the head


The cylinder head does not have to be removed to replace the lifters, however the intake manifold does have to be removed to replce the lifters.

Aug 17, 2010 | 1991 Chevrolet Suburban

2 Answers

Need instructions on how to change the lifters in my 1998 Chevy S10 2.2L


Please don't forget to rate!!!!

2.2L Engine When installing new lifters, a pre-lube should always be applied to the lifter body. It is also a good idea to prime hydraulic lifters by submerging them in clean engine oil and depressing the plunger using an old pushrod. This allows the internal components of the hydraulic lifter to coat with oil before initial operation in the engine. All lifters should be replaced when a new camshaft is installed.
If any valve train components (lifters, pushrods, rocker arms) are to be reused, they must be tagged or arranged during removal to assure installation in their original locations.
  1. Remove the rocker arm cover.
  2. Remove the cylinder head assembly from the engine.
  3. Remove the bolts retaining the lifter anti-rotation brackets, then remove the brackets.
  4. Remove the hydraulic roller lifters from the bores.
  5. Inspect the lifter and lifter bore for wear and scuffing. Examine the roller for freedom of movement and/or flat spots on the roller surface.

a3ab0ce.gif
Remove the bolts retaining the lifter anti-rotation brackets ...


bb0d44a.gif
... then remove the anti-rotation brackets


79533e9.gif
The lifters are located in bores in the engine block


a298166.gif
Use a lifter removal tool to remove the lifters from the bore

To install:
If installing a new lifter, coat the lifter body with a suitable camshaft pre-lube
  1. Install each hydraulic lifter to its bore being careful to align the flat sides (top) of the lifters with the flat sides of the anti-rotation brackets. When properly installed the flat sides of each lifter are aligned parallel to the anti-rotation bracket. The roller at the bottom of the lifter is parallel to the camshaft lobe.
Make sure to properly align and install each lifter as improper installation of the lifters or brackets could result in engine damage.
  1. Install the anti-rotation bracket retaining bolts and tighten to 97 inch lbs. (11 Nm).
  2. Install the cylinder head.
  3. Install the rocker arm cover.

d477687.gif
Removing the hydraulic roller lifter from the 2.2L engine

Feb 06, 2010 | Chevrolet S 10 Cars & Trucks

2 Answers

I just replaced all of my hydraulic lifters and no compression!


Yes, you've overtightened the lifters causing the valves to not close completely. If you did not prime the new lifters before you installed them and tightened them with the engine off they are most likely collapsed. back off all of the rockers to just snug and make sure the engine is running when you readjust them. Usually you need to let new lifters sit in a can of oil for a while to fill up. I've used a syringe to fill lifters prior to installation. Did you replace the push-rods also? If so were they the same length as the originals?

Sep 20, 2009 | 1992 Chevrolet Sportvan

1 Answer

1997 jeep grand cherokee laredo replace collapsed lifter 4.0l il6


What motor do you have? The V8, you can remove just the intake manifold and the valve covers/rocker arms to remove the lifter. The V6, I believe you need to remove the head to access the lifters.

Jun 10, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Oil not getting to back rocker, push rod clear. had a new head gasket put on, pulled head to see if it was put on backwards, it was not. how do you replace lifter.


Since you already have had it apart, you know at what point you can see the lifter. Lifter pulls straight up out of its bore, new one drops right in. If cam contact surface is worn concave, you need to replace cam as well. Always use assembly lube on lifter/cam contact surface when installing.

Apr 23, 2009 | 1990 Chevrolet S 10 4WD

Not finding what you are looking for?
1992 Ford Explorer Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...