Question about 1995 Ford Taurus

1 Answer

1995 3.8l ford taurus water pump

What bolts go were on the water pump

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Please be more elaborate detail shorty's in back the unit should line up

Posted on Oct 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where Is The Oil Pump Located>? And How Do I Replace The Oil Pump


Here you go. BIG Job!

http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

The oil pump is an essential piece of equipment that keeps your Ford Taurus running. It lubricates the engine by keeping the oil circulating. Without this lubrication, the engine wouldn't run. An oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.

How to Check if an Oil Pump Is Bad

Things You'll Need




  • Wrench



  • New oil pump



  • New A/C bolts

Remove Old Oil Pump


  1. Drive your Ford Taurus up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.


  2. Take the engine out and put it on an engine stand then remove the upper intake manifold. Take off the valve covers then the accessory drive belt.


  3. Remove the power steering pump and the alternator. The water pump is the next component to remove, followed by the A/C compressor and bracket.


  4. Rotate the pulley shaft clockwise to remove the crankshaft pulley. It has left-handed threads.

  5. Pull out the oil pan and the oil pump screen and tube. Take off the front cover and the timing chains and remove the crankshaft timing gears. Finally, remove the oil pump, taking note of the bolts you removed and in which order you remove them.

Insert New Oil Pump


  1. Install the new oil pump and put the bolts back on in the same manner you removed them. Tighten these bolts to 71 to 106 in-lb.


  2. Reinsert the crankshaft timing gears, timing chains and front cover. Put the oil pump screen and tube back on, torquing the bolts to 71 to 106 in-lb, and torque the nut to 15 to 22 ft-lb.

  3. Put the oil pan back in, then the crankshaft pulley. Install the A/C compressor and bracket using new bolts for the A/C. Add the water pump, alternator, power steering pump, the accessory drive belt, valve covers and upper intake manifold.


  4. Replace the engine back into your Ford Taurus and fill the crankcase. Start your engine and look for leaks in the area you were working.

Read more : http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

Aug 06, 2015 | 2004 Ford Taurus

1 Answer

I have a 2002 ford taurus and antifreeze is leaking cant tell from where but it is getting all over my belt and causing smoke could this be a simple hose or a water pump im at a loss


Hello! It sounds like the water pump is leaking...But first, inspect your hoses and their clamping points...
if you can observe coolant leaking, running from the center of the rear of the water pump then it's time to replace it see diagram below for bolt torquing sequence...Bolts1-7=18 Ft. Lbs....Bolts 8-12= 89 In. Lbs.

Guru...........Saailer



9_25_2011_12_27_31_am.gifACDELCO Part # 252467

COST $50; RockAuto.com

Sep 25, 2011 | 2002 Ford Taurus

1 Answer

Tell me how to replace the water pump in a 1997 Ford Taurus Duratec engine.


1. Drain the engine coolant
2. Remove the Belt
3. Remove the radiator, and heater hoses from the water pump connections.
4.Remove the brace that connects to the A/C compressor to the water pump.
5. Remove the 4 bolts that secure the water pump to the engine.

I hope this helps you, and I wish you luck on your repair.

Aug 24, 2010 | 1997 Ford Taurus

1 Answer

How do you replace a water pump in a 1994 ford taurus 3.0


first unhookd battery,drain coolant,take serpentine belt off,loosen 5 bolts take water pump off,install new gasket,tight five bolts put serp. belt back on,refill with coolant

Jan 09, 2010 | 1994 Ford Taurus

1 Answer

How to replace a water pump on a 2001 ford taurus


This is for a 3.0L and VIN S engine--

VIN U Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt and tensioner
    • Water pump pulley
    • Heater hose
    • Engine control sensor wiring
    • Water pump
54afbf0.gif
To install:
NOTE The water pump bolts are of different lengths and must be installed in the correct locations.

  1. Install the water pump. Tighten bolts 1, 2, 3, 4, 5, 6, 7, 8, 9 and 15 to 15–22 ft. lbs. (20–30 Nm). Tighten bolts 10, 11, 12, 13 and 14 to 72–106 inch lbs. (8–12 Nm). Refer to the accompanying illustration for the bolt locations.
  2. Install or connect the following:
    • Engine control sensor wiring
    • Heater hose
    • Water pump pulley and tighten the bolts to 15–22 ft. lbs. (20–30 Nm)
    • Accessory drive belt and tensioner
    • Negative battery cable
  3. Fill the cooling system and check for leaks

Dec 08, 2009 | 2001 Ford Taurus

1 Answer

2002 ford taurus wtaer pump


Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jul 04, 2009 | 2002 Ford Taurus

1 Answer

What are specs for water pump bolts for 2001


Home | Account | Contact ALLDATA | Log Out | Help ALL TUNE & LUBE DDG AUTOMOTIVE Select Vehicle | New TSBs | Technician's Reference Component Search: Conversion Calculator 2001 Ford Taurus V6-3.0L VIN 2 Flex Fuel Vehicle Level Specifications Mechanical Specifications Water Pump Water Pump Water Pump Notes Engine Front Cover and Water Pump Assembly 25 Nm (18 lb-ft) © 2009 ALLDATA LLC. All rights reserved. Terms of Use

Jun 10, 2009 | 2001 Ford Taurus

1 Answer

How do I change the water pump on a 97 Ford Taurus V-6


detach the cable from the negative terminal of the battery then loosen the 4 water pump pulley bolts be sure to do this before removing the drive belt then remove the drive belt, alternator, and remove accessory drive belts and idler assembly bolts loosen the hose clamp and detach the heater hose from the water pump and then remove bolts from water pump they around $36.00 at NAPA

Jan 18, 2009 | 1997 Ford Taurus

1 Answer

Water pump


WATER PUMP Removal Disconnect negative battery cable. Drain cooling system. Loosen water pump pulley bolts. Remove accessory drive belts. 1. Remove automatic tensioner. Disconnect coolant hoses from water pump. Remove retaining bolts, water pump and gasket.
Installation To install, reverse removal procedure. Lightly oil all bolt and stud threads, except bolt requiring Thread Sealant, before installing. Apply Contact Adhesive on gasket and install on water pump. 1. Tighten bolts/nuts to specification. Refill cooling system. Check for leaks when finished.

Oct 07, 2008 | 2000 Ford Taurus

1 Answer

Water pump repair 93 taurus


Loosen the side motor mount and carefully jack the engine up a few inches (careful not to damage the pan), bolts will then you will have enough clearance.

Sep 23, 2008 | 1993 Ford Taurus

Not finding what you are looking for?
1995 Ford Taurus Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...