Question about 1998 Mazda MPV

1 Answer

Mazda mpv obd2 connector location

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

Hi all obd 2 sockets have to be when sat in the drivers seat within hands reach and no need of tools to get at it so this narrows it down for you thats the law best of luck yates210456

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is located the ground wire on mazda mpv 2001?


Your ground wire connection for the OBD2 connector is located under the dash just below and to the right of the heater controls. More likely that you dont have power to the connector. Check the 10 amp "ROOM" fuse in under dash fuse box.

May 08, 2016 | 2001 Mazda MPV

2 Answers

Obd2 scan tool don't comunicate with the pcm, what to do?


Carlos, see if there is a fuse blown to the OBD2 port, the obd port some time shares with other accessories/things like cigarette lighter.
Check all fuses, the OBD will not work if fuse is blown.

May 08, 2016 | 2000 Mazda MPV

1 Answer

I have a 92 Mazda MPV. I am trying to replace an air filter but I am having difficulty trying to remove the connector that is attached to to the top of the air filter cover. How do you remove the...


Sometimes dirt clogs it up n leaves it stuck, try tapping lightly to get the dirt out. Locate d clip on the connetor, press it down and pull while holding d other side. Avoid pulling on d wires though.make sure its the connectors u re holding.

Sep 07, 2011 | 1992 Mazda MPV

1 Answer

Hi my 2001 mazda mpv started staling when come to a stop and had very low rpms when idleing. I ran a obd2 test and the idle air control came up and crankshaft position sensor. I changed IAC with new one,...


After I visited the website named "MPVclub.com," I read an article there that shows the crank position sensor to be located on the right side of the motor buy the crank pulley. You can't miss it, it is right in between the crank pulley and the a/c compressor. Go to www.MPVclub.com, then go to forums, which is on the left hand side of the page, go to 00-06 MPVproblems, go to page 2 and go to the bottom of the page to "PO335 Crankshaft position sensor Replacement, you will see the comments and some pics that will guide you to it.
Hope this helps.

Feb 10, 2011 | 2001 Mazda MPV

1 Answer

If anyone out there knows where exactly to locate the transmission control solenoids on a 1998 mazda mpv 4wd model, and could tell me how to access them, please call me and notify me. names leslie...


They are located inside the transmission at the valve body. They can be tested at the wiring connector at the transmission. 3 solenoids total

Feb 06, 2010 | 1998 Mazda MPV

1 Answer

Location of oil pressure switch.


how change oil pressure sensor in 2001 mazda mpv dx

Apr 10, 2009 | 2001 Mazda MPV

2 Answers

2000 mazda mpv diagnostic box


There should be an OBD II plug under  the dash on the drivers side. It might have a cover over it so look real close. That actron will give you generic P codes.

Dec 28, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
1998 Mazda MPV Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...