Question about 1995 Pontiac Grand Am

2 Answers

Alarm - 95 Pontiac Grandam

My alarm button (key chain) if finally broken after 13 yrs. I really don't want to take it to the dealer to fix, I just want to disconnect the alarm. How would I do that? I pull the fuses, but it won't work. What do I need to look for to dismantle the alarm so that I can drive the car without it going off and open it manually.

Posted by on

  • gimmedomeatl Dec 02, 2008

    I have a factory aftermarket alarm on my 1995 grand am. i want 2 fix it but dont really know what to look for in the wiring.

  • TripleTauto
    TripleTauto May 11, 2010

    factory or aftermarket alarm?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

The factory alarm is wired into ignition system I would recommend buying a new remote they are not that expensive. and having programmed. if it is factory should have a gm or delphi part number

Posted on Nov 10, 2008

Factory, I presume. It came with the car.

Posted on Oct 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pontiac grandam 2000 key will not turn to start car wheel unlocked


Pull the steering wheel hard to the left and try turning the key at the same time.

Feb 08, 2015 | Pontiac Cars & Trucks

1 Answer

Vats system


Instructions
    • 1
      Insert your key into the ignition. Turn the key forward until it can go no further, without starting the vehicle.

    • 2
      Press and hold the "Valet/Override" button located under the dash. Hold the button until the blinking LED light on your dash is solid. Switch your "Valet" button to "Off" if you have a button labeled "On/Off." Your alarm should now be reset. If you wish to enable the alarm, repeat these steps to turn the alarm back on.

    • 3
      Remove wires from your battery if you wish to temporarily turn off your alarm. Disconnect the wire connected to the main power source to permanently disarm your alarm. Trace all wires connected to your battery and disconnect them. If you have no familiarity with your vehicle's wiring, you should take your vehicle to a neighborhood installer to disconnect the wires for you.


God bless you

May 31, 2013 | Pontiac Firebird Cars & Trucks

1 Answer

Will a 95 poniac grandam altinator interchange with a 2000 poniac sunfire


Go to e-bay and type in either or both of the alternators, and after searching a few of those offered for sale, you will see a list of all the different cars and models they fit. At accordingly.
Be blessed.

Apr 06, 2013 | 2000 Pontiac Sunfire

1 Answer

How do i retreive codes from 1992 pontiac grandam


Ground the a and b terminal of the aldl. Turn the ignition key to the on position, do not start the car. The check engine light will flash two digit codes. Example.....flash pause flash, flash, flash would equal code 13.

Aug 10, 2012 | 1992 Pontiac Grand Am

1 Answer

Rear hatch release button broke on 1999 pontiac firebird


The tabs that hold the button in are probably broken. The button on my 95 Trans Am had the same problem. Mine was broken in a way that let me use a zip tie behind the button to hold it in place. I'm pretty sure the button is available from the dealer for under $25 if you wanted to replace it. Pretty straight forward replacement. Few screws (7mm head) and a wire connection.

Aug 15, 2009 | 1999 Pontiac Firebird

1 Answer

Need new keychain alarm button


Is this a factory installed alarm system? If so, unlocking the driver door with the key will allow the car to start. If not then you will have to remove the aftermarket alarm system to start the car.
If you have a factory alarm system you can get a new FOB (key chain alarm button) from a ford dealer, but it must be programmed using a scanner , before it will work in your vehicle.

May 23, 2009 | 1996 Ford Explorer

1 Answer

I put a 95 Grand Am Quad 4 dual overhead cam in a 93 GrandAm with a quad 4 single overhead cam in it can I change the wire harness and make it work.


Sometimes the manufacturers use the same main harness for multiple vehicles. Check part number with dealer on both harnesses. If they are the same, likely you will only need to change the engine harness & computers.

Apr 30, 2009 | Pontiac Grand Am Cars & Trucks

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...