A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Roll the window down first, you will need 2 hands. Pull the small cover off that is at the top front of the door pannel. You will then disconnect the wire connector and remove the three 11mm nuts that are holding the mirror in place. Pull mirror out and replace.
If you dont have just that little pannel you will have to remove the door pannel. If you dont have power windows pull the cover out on the window crank and move it to the side, there will be a screw holding the crank in place. Remove it. If you do have power windows remove the window control switch plate (it will just pop up using a small screwdriver) and disconnect the wires. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. Then remove the screws. DO NOT pull directly outward on the door pannel, something will brake. Remove the front door trim panel by pulling it straight upward.Lift and remove the front door trim panel. Then the nuts holding the mirror will be visible, remove and replace the mirror.
If equipped with an accessory switch panel, carefully pry the switch panel up and away from the door panel. Tag and disconnect the switches from the panel.
On 1981-86 models, remove armrest attaching screws.
On 1987-96 models, remove the retainer screws secure the pocket in the molded armrest on the door panel.
If equipped with crank type windows, remove window crank handle with the appropriate clip removal tool.
If equipped with manual remote mirrors, remove the control knob bezel.
Remove inside door handle cover attaching screw and trim plate.
If equipped with door mounted speakers, remove the speaker, and disconnect the speaker wires. For speaker removal and installation steps, refer to .
Remove all external screws securing the door panel. Insert an appropriate prytool between the door panel and door frame to remove the hidden clips securing the panel.
Holding door panel vertical lift straight up to release the upper clip.
Inspect all retaining clips and replace any broken or missing pieces.
Position the door to the door and carefully press on the retainer clips to engage. If a clip will not engage, inspect the mounting hole behind the panel to make sure the clip is properly aligned. Install any panel-to-door retainer screws.
If equipped with crank windows, attach the washer and crank to the window regulator stud.
On 1981-86 models, attach the armrest to the door using the retainer screws.
On 1987-96 models, insert the armrest pocket and secure in place with retainer screws.
If equipped with door panel mounted speakers, attach the speaker wires to the speaker and secure the assembly to the door panel.
If equipped with remote cable mirrors, attach the control knob to the door panel with the retainer bezel.
If equipped with an ashtray, insert the holder assembly, and secure in place with retainer screws. Install the ashtray to the holder assembly.
Position the door handle trim panel around the door handle assembly, and secure in place with the retainer screw.
If equipped with accessory switch panel, attach the harnesses to the switches, and press the accessory plate into the door panel.
Connect the negative battery cable.
Check and make sure all panel components function correctly.
FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.
Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim
panel. Disengage wire connector from switch panel, if equipped Power
Door Lock/Window Connector
Separate door trim panel from vehicle.
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage
clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.
Hope helped with this; remember rated this help. Good luck.
Section 15-03: Speakers
1997 Villager Workshop Manual
DESCRIPTION AND OPERATION
All vehicle sound systems are equipped with radio speakers (18808) located at all four corners of the vehicle. The radio speakers are mounted in the RH front door (20124) and LH front door (20125), as well as behind the quarter trim panels (31012) in the rear of the vehicle. The Ford Super Sound Audio System has the addition of a subwoofer mounted in the RH quarter trim panel.
Radio Speakers, Front Door
Remove the front door trim panel (23942). Refer to Section 01-05 .
Trim Panel(s), Door
Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
Remove the three cover caps and front door trim panel screws.
Remove the one front door trim panel capped screw from the door pull handle.
If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
Remove the front door trim panel.
Door Electrical Connections Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks.
Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
Remove the front door watershield by carefully detaching it from the adhesive.
If the car is an 03 galant it is very simple to remove.
Remove the window crank if it is not Electric Window.
Remove the Screw that holds the "Open Door Handle" cover.
Remove the Screw that holds the "Pull Handle Pocket"
Remove both plastic covers.
Remove all 3 hidden crews that have a plastic cover over them.
One is toward the front of the door top and the other two are toward the rear of the door top and bottom side.
Carefully pry around the door trim panel to disengage it from th retaining clips, along the sides and bottom. If you have electric windows, disconnect the if from the door trim to access the speaker. Same procedure for both doors.
this is from a 97 civic should be the same. remove the door panel. remove 1 screw and pull handle, remove 1 screw and plastic cover over door opener handle. remove speaker cover and three screws underneath. remover window crank. then remove the door panel (held on with plastic plugs...just pull panel toward youself).
to remove the regulator ("window crank gears") Remove the glass held in with two 10mm bolts. The regulator itself is held in with six 10mm bolts. Remove these bolts and remove the regulator. (installation is reverse). Note: pay attention to the Idler arm track (highlighted in green) I think this one is directional (the front has to be at the front and the back has to be at the rear)
If you have manual windows, remove the window crank handle. Then remove the screw from the trim around the door handle and pry the trim from the door. If you have power locks, disconnect the lock connector from the trim and set it aside. Now remove the panel screws from the bottom of the door (either four or five). You should now be able to pull the panel away from the door at the bottom and then lift it up and away. Once the panel is removed from the door, disconnect the speaker connector.
remove the front door pull cup screw
remove the screw cap and screw from inside handle and slide the handle rearward to disengage the hook from the inner sheet metal. disconnect inside handle from latch remote link if manual windows- remove crank with store bought remover tool. Remove the 2 pushpins from the door trim panel using trim tool pry away door panel  fasteners holding panel and push panel in and up . if elect windows disconnect switches
Remove the front door speaker. For additional information, refer to Section 415-00.
Remove the speaker watershield.
Remove the 2 speaker standoffs.
If equipped, remove the window regulator handle.
Separate the handle cover from the handle.
Remove the screw.
Remove the window regulator handle.
Remove the spacer.
Remove the window control switch. For additional information, refer to Section 501-11.
Remove the bolt.
Remove the 2 front door lower bolts.
Remove the door handle cover plate.
Remove the 2 door handle screws.
Remove the front door handle.
Guide the door handle through the opening in the trim panel.
CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.
Remove the front door trim panel.
Lift upward to remove the front door trim panel.
To install, reverse the removal procedure.