Question about 1996 Honda Accord

1 Answer

1996 Honda Accord High Mount Brake light Cover wont come off.

I have a 1996 Honda Accord, my high mount brake light bulb has fused. I saw the owners manual and it showed that the cover simply comes of. Mine would just not budge. The manual wasn't any help regards and latches there are no screws.

Help most appreciated.

Kind Regards
CM

Posted by on

1 Answer

Http://wiki.answers.com/Q/How_do_you_change_the_high_mount_center_brake_light_bulb_in_a_1996_Honda_Accord

Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the high mount stop light not working?


The same 15amp fuse for the regular brake lights powers the high mount light. If the regular brake lights work but the high mount does not, it could be the lamp monitor or a wiring problem.

Aug 02, 2014 | 2003 Toyota Corolla

1 Answer

How to change high mount brake light bulb in a 2002 lincoln navigator


Instructions
    • 1 Open one of the rear doorsicon1.png of the LS. Position yourself on your knees in the back seat, facing the rear deck or rear dash.
    • 2 Remove the cover from the high-mount brakeicon1.png light assembly, by hand. Pull the cover toward the front of the vehicle. Do not pull extremely hard, or you will break the clips that mount through the deck from the trunk.
    • 3 Pull the old light bulbsicon1.png out of the high-mount assembly. Wrap the new bulbs in a paper tower prior to picking them up. Insert new bulbs into the assembly, by hand. Do not touch the bulb lenses with your hands directly.
    • 4 Install the high-mount cover onto the rear deck and push the cover toward the rear glass to lock it in place.


Read more: http://www.ehow.com/how_10060583_replace-upper-brake-bulb-2001-lincoln-ls.html#ixzz30cNQ559F

May 03, 2014 | Cars & Trucks

1 Answer

No brake lights 2003 Ford Explorer but high mount works


maybe the one of the contacts on the bulb broke or the brake fuse

Aug 06, 2012 | 2003 Ford Explorer

1 Answer

Does the brake switch also operate the high mount brake light


Hi,
Get the original bulb for that 3rd brake light from the dealer parts center.
Tell them( parts dealer center ) the model of your vehicle and they will provide necessary part.

Hope that helps!

Nov 30, 2011 | Dodge Cars & Trucks

1 Answer

Can't find the fuse for brakelights on 2003 Honda Civic!!


look for a symbol of a light with a brake pedal next to it in the handbook or the fusebox cover, or maybe a circle with a pedal in it. it doesnt sound like the fuse though as the the centre light is still working from what i can gather and all three lights will be wired on the same cicuit so will have the same fuse. to avoid any wasted time and money i'd recommend checking the bulbs first, then i'd be checking for power at the bulb holder with a voltmeter or test lamp. hope this helps

Jul 17, 2010 | 2003 Honda Civic

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount...


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

Feb 15, 2010 | 1999 GMC Jimmy

1 Answer

How to: Replace high-mount brake bulbs Mazda MPV 2002


It will be either on the outside with 2 small screws or more likely you need to remove a trim/cover of the top headliner area... If still in doubt goto or phone the dealer and just ask the parts dept person to show it to you...

Jan 28, 2010 | 2002 Mazda MPV

1 Answer

Replaceing brake lights on the trunk assembly part, how do i get to the lights?


High-Mount Brake Light NOTE: Depending upon the vehicle, the center high-mount brake light may be accessed from outside the vehicle, through the trunk, or through the passenger compartment.
  1. Remove the center high-mount bracket light lens retaining screws.
Fig. 17: Use a screwdriver to unfasten the center high-mount lens retaining screws . . .

0379160.jpg
Remove the lens in order to get to the bulbs.

Fig. 18: . . . then remove the lens for access to the bulbs

c49ad34.jpg
Carefully pull the bulb away from its retaining clip contacts.

Fig. 19: Pull the light bulb from the retaining clips

e0d87c6.jpg
Installation is the reverse of the removal procedure. Before installing the lens, make sure the brake light operates properly by having an assistant depress the brake pedal.

Jul 26, 2009 | 1999 Pontiac Bonneville

2 Answers

Stop lamps wont work 93 ford explorer


is it a seperate fuse ??
if its not the fuse check that the wires are connected ok!
Is there power at the switch ??

Jul 17, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...