Question about 1995 Land Rover Discovery

2 Answers

Hi, i have a manual Landrover Discovery 300Tdi, 1995 M reg. Upon taking up drive there is a clonk from the transfer box where the front propshaft comes out. Is this a repairable area or is it easier and cheaper to just change the transfer box? Many thanks, Mark

Posted by on

  • Andy in Thun May 11, 2010

    Are you sure the noise is coming from the transfer box itself ?, it could be coming from a worn universal joint or UJ as they are known that are situated at either end of the propshaft, UJ's are about £10 pounds and a couple of hours labour could solve your fault

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 275 Answers

All Land rovers suffer from clonks in take upo of drive. Most common is that the gearbox mainshaft not only wears itself but also wears the input gear of the transfer box. They can also exhibit this problem from other parts such as drive shaft and drive plate spline wear, worn radius arm bushes, A frame top ball joint, engine and or gearbox mountings. If the clonk is coming from the prop shafts, then by the time you hear or feel the clonk, the prop shaft is propably for throwing. They have big problems with prop universal joints and usually are replaced quite often.
Hope this helps

Posted on Feb 13, 2009

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 53 Answers

Its cheaper to get a recon part.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to removing a transmission from a GMC ENVOY 2004 V6, 4WD.


Park the vehicle in a clean dry well lit place. Work with safety in mind. Its always good to take pictures as you strip the/ a assembly. Refer back to pictures if you get stuck. Dis-connect the battery. Remove the gear linkages and speedo-drive and power cables from the gearbox. Remove the starter motor. Loosen the propshaft. Mark the yokes of the propshaft- for upon installation to avoid an unbalanced propshaft. Loosen the centre bearing. Remove the propshaft. Remove the cross member underneath the gearbox if there is one. Loosen bolts around the gearbox to cylinder block. Use a gearbox jack to support the gearbox. Take the bolts out from the gearbox to cylinder block. Pull gearbox backwards. Lower the gearbox. This is pretty much the standard way of removing gearbox. Note, there might be a transfer box, normally with 2 propshafts. Mark the yokes. Remove propshafts, transfer box and then gearbox. Remember to always work safe.

Dec 19, 2014 | Cars & Trucks

1 Answer

My Landrover Discovery 300tdi 1995, loses power drastically to almost stopping point. failing to climb steep hills and check engine comes on, only going off when I stop accelerating. This has been gradual...


replace ignition coil, spark plugs, also double chek your coolant temperature must be normal. overheating causes car slows down and engine cant handle excessive high temperature or may damage it.

Jan 11, 2011 | 1995 Land Rover Discovery

2 Answers

How easy is it to change glow plugs in a 1995 (N reg) discovery?


should be handy enough just screw out put new one in
if your machine hard to start when heating in the morning ,wait twenty seconds after light goes out then crank it
heater relay still working when heat indicator light goes out

Feb 25, 2010 | 1995 Land Rover Discovery

2 Answers

Engine turns over very slowy.


check battery connections are clean and tight check main engine to body earth cable for condition and security check connections at starter motor to check for engine earth problem put a good quality jump lead between bat neg terminal and engine crank and see if ok

Jan 22, 2010 | 1995 Land Rover Discovery

1 Answer

Landrover discovery, automatic... i cannot


could be eithor

AAMCO gives free estaments and they are the experts in this feild

Jan 19, 2010 | 1995 Land Rover Discovery

1 Answer

Landrover discovery 300tdi 1995


sounds like a blocked filter or low pump pressuer

Feb 18, 2009 | 1995 Land Rover Discovery

3 Answers

Gear box


Hi Steve, without knowing a bit more about your disco, ie, age, 200 or 300tdi, can you get all the gears when in 4x4 ?,it might be difficult to pinpoint your fault, but going on your first description i would say that the high range on your transfer box could be the problem. Do you have a local transmission repair workshop to you?, they should be able to confirm this for you

Jan 21, 2009 | 1995 Land Rover Discovery

1 Answer

No drive 300tdi 1996. recon engine


maybe the linkage in the transfer case is busted that could be where the noise is coming from . hope this helps

Jan 05, 2009 | 1996 Land Rover Discovery

1 Answer

I am trying to find out if the wiring is in my landrover 300tdi


any aftermarket lights have to have the wire loom ran. when you run the loom make sure that it is protected and out of the way of things. also when going through any peace of steel make sure that you use a gromet so the wires don't get cut.

Dec 09, 2008 | 1998 Land Rover Discovery

1 Answer

Cylinderhead bolts torque settings


According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.

Nov 29, 2008 | 1994 Land Rover Discovery

Not finding what you are looking for?
1995 Land Rover Discovery Logo

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...