When the tire pressure is normal in all of the tires the light should go out other wise you will need the Kent-moore TPMS tool to check for a bad sensor and setting the monitors locations. so it may be easyer to take it to a GM Dealer if light does not go out
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
After checking/adjusting all tire's pressure (including spare, some spares have a tire pressure sending unit), turn ignition "ON" (NOT "START", just the position key is at when you are driving).
Press the MODE button until LOW TIRE PRESSURE HOLD SET TO RESET is displayed.
Press and hold the SET button until a chime sounds and TIRE PRESSURE RESET is displayed and a chime sounds 3 times.
Release the SET button and TIRE PRESSURE NORMAL is displayed.
By operating the tire pressure warning reset switch, the tire pressure warning ECU can be set to issue a warning at an inflation pressure that corresponds to the standard pressure of tires .Therefore, you must set the warning threshold to the proper value in order to comply with the local regulations .Operate the tire pressure warning reset switch only after the inflation pressures of all tires have been adjusted on the vehicle.To initialize the system, press and hold the tire pres- sure warning reset switch for 3 seconds or longer with the ignition switch in the ON position. When the system receives the
initialization signal, the warning light blinks 3 times (1 second on, 1 second off). During initialization, the tire pressure warning valve and transmitter measures the inflation pres sure of the tire, and registers the signals that are transmitted into the tire pressure warning ECU at a frequency of once per minute. The initialization process is completed when signals from all the tires have been received. It takes a few minutes .
Tire size Inflation Front Inflation Rear
P 195/65 R15 89S 30 psi 30 psi
195/65 R15 91H
P 205 /55 R16 89H 32 32 psi
P 215/45 R17 87W
205/55 R16 91V
definetly tire prssure low light. you can reset it by scrolling through the mileage and trip meter once you get to the screen for the tire preesure monitor hold the button down till it flashes and it will reset. make sure you check all your tire pressures first.
1. check and make sure that your tires are inflated to the correct pressure
2. turn the ignition switch to the ON position. If the low tire
pressure warning light comes on, push and hold the tire pressure
warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns
off and then release the switch.
3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.
4. initialization is *not* completed until driving at the vehicle speed
of 19 mph or over for more than one hour. the tire pressure monitoring
starts when initialization is completed.
Because of changing outside temps this happens, just hold reset button on left side of dash until it reads tire pressure 100% again, just make sure your pressure is right before you do it. this is the same for oil changes and the like.
Your nissan also has a tire monitor on your spare tire if your spare has low pressure and the other 4 tires have correct pressure the light will stay on . after you ajust the spare also the light should go away.
Vehicles Without Message Center
To reset the system, press and hold the odometer reset button and wait for the "TIRE PRESSURE SET" light to illuminate. Continue to press the button for 3 seconds, then release. After 3 seconds, the low tire pressure warning lamp will flash 3 times, indicating that the low tire warning system reset procedure is complete.
Vehicles With Message Center
To reset the system, press and hold the SETUP button and wait for the message center to display "REST FOR SYSTEM CHECK". Then press the RESET button and wait for the message center to display "HOLD RESET TO RELEARN". Press and hold the RESET button for 3 seconds. The message "HOLD RESET TO RELEARN" and the low tire warning lamp will flash 3 times, indicating the reset procedure is complete.
Reset without message center:
To reset turn the ignition to the ON position, depress and Trip/odometer
button (located in the instrument cluster) until “TIRE RESET” or
“CHECK TIRE AND RESET” is displayed in the odometer display window.
Once “TIRE RESET” or “CHECK TIRE AND RESET” is displayed,
press and hold the button for three seconds. The low tire warning indicator light will flash three times
as the low tire warning system begins to initialize.
Reset with message center:
To reset turn the ignition to the ON position, press the set up button on
the message center until “SYSTEM CHECK” is displayed. Press the
RESET button until “HOLD RESET TO RELEARN” is displayed, continue to hold the button for three
seconds. The low tire warning indicator light will flash three times as the low tire warning system begins to initialize.