Question about 2003 Jaguar X-Type

1 Answer

I want to be able to replace my reverse aid module myself.

I ahve had 2 repairs of this device and its pricey, could I do it myself at novice level?

Posted by on

  • karl siasico May 11, 2010

    the problem of fixing things just by yourself is that you dont have the complete set of tools to use. but if you have tools then im sure you can do it. which part of your car are you gonna fix anyway?

×

Ad

1 Answer

I want to change the reverse aid module, for the back sensors

Posted on Oct 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is backup light switch on 01 impala


Backup Lamps
The B/U LAMP fuse in the RH I/P fuse block supplies battery positive voltage to the switch terminal of the backup lamps relay. The DIC/RKE fuse supplies battery positive voltage to the backup lamps relay coil terminal. When you place the gear selector lever in the REVERSE position, the powertrain control module (PCM) sends a class 2 message to the body control module (BCM). When these conditions occur, the BCM energizes the reverse lamp relay control circuit, closing the switch contacts, the current flows from the reverse lamp relay switch to the backup lamps. The backup lamps are grounded at G302.

There is alot involved in turn on the back up lights .
DTC B2552
Circuit Description
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamp relay control circuit which energizes the backup lamp relay.

2
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the backup lamp relay ON and OFF.
Does the backup lamp relay turn ON and OFF with each command?
YES - Go to Diagnostic Aids
NO - Go to Step 3

DTC B2553
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamps relay control circuit which energizes the backup lamp relay.
Turn the ignition ON.
Shift the gear selector lever to the REVERSE position.
Do the backup lamps turn ON?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Remove the backup lamps relay.
Connect a test lamp between the battery positive supply voltage circuit of the switched side of the backup lamp relay and ground.
Does the test lamp illuminate?
Before replacing parts you may not need , take your vehicle to a qualified repair shop .

Aug 16, 2016 | 2001 Chevrolet Impala

1 Answer

Where is the Parking Aid Speaker located on a 2005 Ford Explorer?


Parking aid speaker attached to the parking aid module.



  1. Remove the RH quarter trim panel. For additional information, refer to Section 501-05 .




  1. Disconnect the parking aid module electrical connector




  1. Remove the bolt and the parking aid module.




  1. To install, reverse the removal procedure


  2. The parking aid system is disabled if a fault is detected in one of the 4 sensors, the parking aid speaker, or the parking aid module. This is indicated by the parking aid disabled warning. The parking aid module is on the international standards organization (ISO) 9141 network and can be diagnosed with a diagnostic tool.



  3. Rear Quarter Trim Panel

    Removal and Installation



    All vehicles




    1. Remove the rear door scuff plate.





    1. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel in this section.





    1. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section.





    1. Remove the liftgate scuff plate trim panel.



    Vehicles with third row seating




    1. Remove the third row seat. For additional information, refer to Section 501-10 .





    1. Position the liftgate opening weatherstrip aside.



    All vehicles




    1. If equipped, remove the luggage assembly cover.





    1. Remove the stowage compartment doors.





    1. NOTE: RH side shown, LH side similar.


      Remove the stowage compartment assembly.





    1. Position the carpet aside.





    1. Remove the brackets.



      • Remove the bolts.







    1. Remove the rear quarter trim panel.

Feb 26, 2015 | 2005 Ford Explorer

1 Answer

Temp gauge in 98 pontiac wont work is there a fuse for it


Hi Tammie, Is the coolant level low ? If not , The engine coolant level switch grounds the indicator with the coolant level in the coolant reservoir below the minimum recommended level. The engine coolant level indicator module is on the right side of the radiator just down below from the radiator cap !
Low Engine Coolant Indicator Always On

Step

Action

Value(s)

Yes

No

1

  1. Disconnect the engine coolant level indicator module connector.
  2. Turn the ignition switch to the RUN position.

Is the low coolant warning indicator ON?
--
Go to Step 2
Go to Step 5

2

Inspect for a short to ground in CKT 68.

Does a short to ground in CKT 68?
--
Go to Step 3
Go to Step 4

3

  1. Repair the short to ground in CKT 68.
  2. Inspect the system.

Is the repair complete?
--
System OK
--

4

  1. Replace the instrument cluster. Refer to Instrument Cluster Replacement .
  2. Inspect the system.

Is the repair complete?
--
System OK
--

5

  1. Replace the engine coolant level indicator module. Refer to Coolant Level Module Replacement in Engine Cooling.
  2. Inspect the system.

Is the repair complete?

Feb 01, 2015 | 1998 Pontiac Grand Prix

1 Answer

How to replace the winshield washer fluid resevoir 2001 pontiac grand am 3.6L


  1. Remove the left front fender liner.
  2. Remove the air intake duct.
  3. Remove the connector from the washer pump.
  4. Remove the hose from the washer pump.
  5. Remove the connector from the level sensor.
  6. Remove the brake control module.
  7. Remove 3 screws and the washer solvent container from the vehicle.

    Reverse to install.

Oct 17, 2012 | 2001 Pontiac Grand Am SE

1 Answer

2000 Lincoln LS Right rear turn signal is not working. The front right signal is working, but the "blinking" rate is faster than normal (like a flasher being bad - from the good old days). I...


had same problem. turned out to be water/moisture in rear tail light assembly. Drilled 2 small holes in lens to drain water and let assembly dry out. cleaned bulb socket and in serted new bulb.

Jul 11, 2011 | 2000 Lincoln LS

1 Answer

I have a 2006 explorer with the rear sensing system RSS my warning does not work and there is a warning on the dash stating to check rear backup system? The fuse should be good as my heated seat and 4x4...


Have the RSS module checked for DTC'S - diagnostic trouble code's . That should always be the first step . An it is
Reverse sensing system Parking Aid The parking aid system consists of the:
  • parking aid sensors
  • parking aid speaker
  • parking aid module
The parking aid system is activated when the parking aid module receives a network messages from the instrument cluster indicating that the vehicle is in reverse. The parking aid system sounds a warning to alert the driver of stationary objects near the rear bumper when REVERSE is selected. The parking aid system assists the driver in detecting certain objects while the vehicle moves in reverse at speeds less than 4.8 km/h (3 mph). The parking aid system may not detect angular or moving objects.

  1. Visual Inspection Chart Electrical
    • Smart junction box (SJB) fuse 18 (10A)
    • Circuitry
    • Connector(s)
    • Parking aid sensors
    • Parking aid speaker
    • Parking aid module
Do you know what DTC'S are .

Parking Aid Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1299 Power Supply Sensor Circuit Short to Ground Parking Aid Module Go To Pinpoint Test C . B1342 ECU is Faulted Parking Aid Module CLEAR the DTCs. REPEAT the parking aid module self-test. If DTC B1342 is retrieved again, INSTALL a new parking aid module. REFER to Parking Aid Module in this section. CLEAR all DTCs. REPEAT the self-test. B2477 Module Configuration Failure Parking Aid Module REFER to Section 418-01 . C1699 Left Rear Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1700 Left Rear Sensor Circuit Failure or Blockage Parking Aid Module Go To Pinpoint Test C . C1701 Left Rear Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1702 Right Rear Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1703 Right Rear Sensor Circuit Failure or Blockage Parking Aid Module Go To Pinpoint Test C . C1704 Right Rear Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1705 Left Rear Center Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1706 Left Rear Center Sensor Circuit Failure Parking Aid Module Go To Pinpoint Test D . C1707 Left Rear Center Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1708 Right Rear Center Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1709 Right Rear Center Sensor Circuit Failure Parking Aid Module Go To Pinpoint Test C . C1710 Right Rear Center Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1742 Rear Sounder Circuit Failure Parking Aid Module Go To Pinpoint Test F . C1743 Rear Sounder Circuit Short to Battery Parking Aid Module Go To Pinpoint Test F . Your best bet , take it to a qualified repair shop . Ford

Jan 02, 2018 | Ford Explorer Cars & Trucks

2 Answers

My 2007 Yukon has a problem with the park assist sensors. When I go in reverse sometimes, the warning beep repeats quickly and the lights flash like crazy but nothing is behind the vehicle. Sometimes the...


Check the system for DTC'S - diagnostic trouble codes should be the first step in the diagnostic process . Then reading factory service repair manual how the system works , viewing wiring diagrams .
Object Detection Description and Operation
Ultrasonic Rear Park Assist Operation
The ultrasonic rear park assist system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located in the rear bumper. The object detection system will notify the driver when backing up at speeds less than 8 km/h (5 mph). The object detection system will use the rear parking assist (RPA) display and the radio speakers for notification.
When the ignition is ON and the vehicle is placed into reverse, the object detection system performs a bulb check. During the bulb check, the 3 indicators on the RPA will illuminate for approximately 2 seconds to indicate that the system is working. The object detection system performs a bulb check and operates when the following conditions are present:
• The ignition is ON.
• The vehicle is placed in REVERSE (R) for rear parking aid.
• The vehicle speed is less than 8 km/h (5 mph). At speeds greater than 8 km/h (5 mph), the object detection system is disabled. The red indicator flashes to warn the driver that the object detection system is disabled.
The object detection system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located on the rear bumper. When the system detects an object, one of the following will occur:
• If the object is less than 0.3 m (11 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators flash and the chime sounds continuously for 3 seconds.
• If the object is less than 0.3-0.5 m (11-20 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators are ON.
• If the object is 0.5-1.0 m (20-40 in) away from the vehicle, the amber outside, and the amber middle indicators are ON.
• If the object is 1-2.3 m (40-91 in) away from the vehicle, the amber outside indicator is ON with a single chime when the object is first detected.
Object detection system can detect objects 7.6 cm (3 in) wide and at least 25.4 cm (10 in) tall. It cannot detect objects above the level of the roof.
If the object detection system detects a malfunction, a diagnostic trouble code (DTC) will be stored and the object detection system will send a serial data communication message to the instrument panel (I/P) to SERVICE PARK ASSIST message on the driver information center (DIC). Then the chime will sound and the red indicator on the information telltale center will be lit continuously. The red LED in the rear display will be lit, notifying the driver that a malfunction exists. Message will clear once the driver acknowledges it.
Each object sensor is a three wire sensor that is both a transmitter and a receiver that comprises a signal circuit, a low reference circuit, and an 8-volt supply voltage circuit. The rear object control module supplies 8 volts to the object sensors via the object sensor supply voltage circuit and provides ground via the low reference circuit. The rear object control module triggers the sensors in a sequential loop and after each sensor transmits, the rear object control module uses the echo or signal return to calculate the distance and position of an object from the rear bumper. The rear object control module directly controls the RPA display.

Do you know what DTC'S are ?
DTC B0958 01: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Battery
DTC B0958 06: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Ground or Open
DTC B0958 08: Parking Aid Rear Sensor 1 Left Corner Circuit Signal Invalid
DTC B0958 21: Parking Aid Rear Sensor 1 Left Corner Circuit Incorrect Period
DTC B0959 01: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Battery
DTC B0959 06: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Ground or Open
DTC B0959 08: Parking Aid Rear Sensor 1 Left Middle Circuit Signal Invalid
DTC B0959 21: Parking Aid Rear Sensor 1 Left Middle Circuit Incorrect Period

DTC B0967 02: Parking Aid Switch Circuit Short to Ground
DTC B0968 00: Parking Aid Indicator Circuit


Your best bet , take it to a qualified repair shop.

Feb 04, 2018 | GMC Yukon Cars & Trucks

1 Answer

I have the rss reverse sensors and when i put the truck in reverse the light illumes off and the system wont alarm


Check the park aid sensor lenses for damage.

Next remove the park aid sensors ( remove from the back of the bumper ) and check for damage.

Check the connectors on the sensors for corrosion or damage.

The symptom you describe is usually the park aid module cannot test the sensors ( or they fail test )

Oct 23, 2010 | 2004 Ford F150

1 Answer

2003 Tahoe intermittantly won't start


Sounds like an ignition switch, I believe there are 2 different switches a 10 pin and a 14 pin and they are made of plastic and they are kind of pricey. Cant say how hard they are to change have never run into a bad one yet

Jun 21, 2009 | 2000 Chevrolet Tahoe

Not finding what you are looking for?
2003 Jaguar X-Type Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77514 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...