Question about 1992 Ford Ranger

1 Answer

1997 Ford Ranger

Need help with installing a slave cylinder and a clutch please.....Thank you!

Posted by on

  • yadayada
    yadayada May 11, 2010

    What kind of help do you need

  • yadayada
    yadayada May 11, 2010

    Whatkd of help do you need?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Teeth dont line up . on the old clutch the teeth are pushed back. the new clutch the teeth are out more which causes problems lining up. is there a method to line up and/or push the teeth in more

Posted on Jan 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to drop trans to install slave cylinder on 95 ford ranger


I know the regular sized Ford pickups had the slave cylinder inside the bellhousing, requiring transmission removal for replacement (not very smart, Ford!) So I suppose your Ranger, too, if you don't see the cylinder on the outside.; Most people who go through this replace the whole clutch and the slave cylinder at the same time, to avoid having to do it over again.

Nov 05, 2012 | Cars & Trucks

1 Answer

JUST INSTALLED NEW CLUTCH, SLAVE CYLINDER AND MASTER CYLINDER ON 1986 FOR RANGER. CAN NOT GET CLUTCH TO BLEED, JUST ABOUT THE TIME I GET SOME CLUTCH, THE SLAVE SEAL STARTS LEAKING AT THE SEAL BEHIND THE TO...


The slave should not leak. Either it is defective, or there is a mechanical problem with the clutch pressure plate or throwout bearing, and the slave it over extending.

Jun 25, 2011 | Ford Ranger Cars & Trucks

2 Answers

Having problems with the clutch in my 1998 Ford Ranger. There is no freeplay, and it is very difficult to shift. Do I need to adjust the clutch? If so, how do I adjust it?


The clutch is not adjustable,it is a fluid clutch.It has to be a leak,or the slave cylinder,and,or, the master cylinder are bad,It does not have to be leaking to be bad,but it is one of the two.Rate please,thank you.

Jul 12, 2010 | 1998 Ford Ranger SuperCab

1 Answer

How to install a slave cylinder on a 95 ford ranger


The easiest way to deal with this problem is to order the complete preblead slave cylinder kit.
You can, just go with a new slave cylinder but because of the age of the other parts. You may run into other problems down the road. Why have to do it twice.
To replace the slave cylinder only:
Its easy, just carefully push/remove the small metal pin that hold the plastic line to the slave cylinder. then push-in and turn counterclockwise, to remove slave cylinder. Then install new slave cylinder and reverse the procedure. Now bleeding the system will take a while. But all you will do is just keep pumping the clutch pedal until the pedal returns.

May 18, 2010 | 1995 Ford Ranger Supercab

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

1 Answer

1993 Ford Ranger 4x4 clutch slave cylinder


In my experience, the main cause of a problem like this is either due to incorrect installation or not using an OEM slave cylinder! As far as the clutch wear, when replacing a clutch it is absolutely necessary to have the flywheel machined at a machine shop!

Jul 31, 2009 | 2003 Ford Ranger Regular Cab

2 Answers

89 ranger manual trans slipping already replace clutch and slave cylinder? still slipping any help?


Manual transmissions do not slip ie. when the gears mesh, there is no slip unless they strip out and make an awful noise and will not pull henceforth.

You probably still have a slipping clutch plate against the flywheel. You need to adjust the clutch petal linkage shaft to allow the pressure plate to be release from the thrust bearing, ie shorten the shaft length.. If you and most likely you do just have the clutch release slave cylinder that releases the clutch when you apply the petal. You need to bleed the slave cylinder of any excess fluid or air that may have entered the line if you opened it at any point. You need to bleed it as you would a break cylinder and this should fix ya.
good luck.
good luck

Jan 05, 2009 | 1989 Ford Ranger

2 Answers

Brake fluid in brand new 1989 ford ranger clutch slave


no it doesn't come filled basically you bleed it like a brake system. Fill the master cylinder and pump the clutch, there is a bleeder on the slave cylinder

Dec 08, 2008 | 1989 Ford Ranger

1 Answer

2001 ford ranger clutch


have you check the slave cylinder to see if its moving when someone puts there foot on the clutch.
And check the adjustment on the master cylinder.

Sep 18, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...