Question about 2000 Jeep Grand Cherokee

1 Answer

Turn signal light

How do you replace a turn signal light, juswt one bulb?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

Take the lens screws out remove the lens and replace it from the back.

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6


hello,
  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    Left turn signal lights but will not flash


    Check and make sure both front and rear left turn signal bulb light up, if they do, replace the turn signal flasher, flasher sit under dash in fuse box, if one or both bulb don't light up, replace bulb.

    Sep 20, 2010 | 1995 Buick Century

    1 Answer

    I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


    Hi!!

    If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

    Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

    Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

    If front turn lights work fine, check brake/turn bulbs.

    If turn lights come on but don't blink, replace turn signal/hazard flasher.

    If front and back turn lights don't come on, replace switch on column.

    Let me know how it worked out, Good Luck

    Mar 24, 2010 | 1991 Plymouth Acclaim

    1 Answer

    Bulb failures with no real pattern


    check the front and rear turn signal and brake bulbs ,check for filament wear or drakness in bulb glass.if this is found replace bulb,you may also have a bad ground to a bulb socket, turn lights on (signal and break) and wiggle wires at bulb socket, watch light, if it dim any replace that socket and check the ground wire.

    Mar 04, 2010 | 1989 Jaguar Vanden Plas

    2 Answers

    Tail lights work on both sides. turn signal and


    Sounds like you need to replace the drivers brake/tail light.

    Dec 14, 2009 | 1998 GMC Sierra

    2 Answers

    2005 mustang right turn signal wont work but bulb lights when lights are on. When signal is on only the first bulb blinks (and twice as fast as left signal) and second signal bulb doesn't work at all.


    Replace the bulb(s). Tail light bulbs have more than one filament. One is for the brakes and one is for the turn signals. The reverse light is a light all by itself. When the filament for the turn signal goes out the brakes will still all light up, but the turn signal will not.

    Oct 31, 2009 | 2005 Ford Mustang

    1 Answer

    The drivers side rear brake light/turn signal only not working


    you replaced the bulb with the wrong one i.e. a two filament bulb with a one filament bulb

    Oct 05, 2009 | 2006 Ford F-250 Super Duty

    2 Answers

    Need replace turn signal bulb


    YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

    Aug 24, 2009 | 1996 Chevrolet Cavalier

    Not finding what you are looking for?
    2000 Jeep Grand Cherokee Logo

    Related Topics:

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    60867 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...