Question about 1990 Mitsubishi Mighty Max

1 Answer

95 Mighty Max, standard, starts but won't move when in gears.

It's a standard trans, I put it in gear and it won't move, bogged down and stalled, wouldn't start, got it home, it starts, but will not move when shifted into gear.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 69 Answers

Check the oil level in the rear end it may be very low or empty if that isnt it have the clutch looked at

Posted on Oct 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 jeep liberty won't move when put in gear (like brakes are locked).crank it in neutral put in gear it will go till i touch brakes then won't move again.WHAT'S WRONG WITH THIS THING.


gear, is this a Manual trans? or AUTO you said gear.
what gear, please name the gear, 1,2,3,4,5 R
or PRNDL ( a/t box auto matic) what shift lever selection?
what is out door air temp, you do know brakes can get wet and freeze right?
it wont go you meant? until brakes are touched, key word won't?

ok engine only starts in PRNDL set to N??
is that it?
and then when you shift to D, the car will not move
what about the other gears.? try them all yet?

my guess (wild) is that you dont know how park lock out works.?
that you must hold the brake pedal down to shift to park or neutral.
is that it? (read operators guide?)

my guess is car is not drive-able. key point1 (a dead car)
point 2, engine starts and runs. and races on demand with gas foot.
point 3, im lost. (no trans stated or clear symptoms.)

my jeep has 6speed manual box
and the clutch allows me to start car.
on Automatics trans must be in park or neutral to crank engine.

"it will go till i touch brakes"



I read that 10 times,
my 2nd guess. the engine stalls ?

IS THAT IT, stalls means engine RPM is 0
and right foot actions are dead.
and all dash lamps glow, telling you STALL is now.

Feb 26, 2015 | 2004 Jeep Liberty

1 Answer

Steering wheel is locked on my 95 ford f150 xl..it starts and goes into gear but the steering wheel won't move..it is locked


you can break the lock by pulling down on the steering whell very hard. or if your ignitons swith is bad you have to get a new one

Nov 13, 2011 | 1995 Ford F150 Styleside Regular Cab

1 Answer

1991 mighty max only goes 10mph in each gear before stalling makeing my top speed about 45mph. I have tried everything i can think of any suggestions??


SOUNDS TA ME LIKE UR CADELITICE CONVURTER IS CLOGED UP...TAKE IT OFF AND HOLLOW OUT WIT A LONG SCWER DRIVER AND JAM IT DOWN THROW WHAT COMES OUT WILL B HONEYCUMB IN SHAPE SHAKE REMAINING PEICES OUT AND PUT BACK ON...IV HAD THE SAME PROBLEM IN THE PAST AND THIS HAS WORK FOR ME

Nov 04, 2011 | 1991 Mitsubishi Mighty Max

1 Answer

When i start my 1990 mitsubishi mighty max pick up , it will idle , but when i give it gas it bogs down ?


it may be the cataltic converter pluged start it and give it gas for a few minutes and see if it gets cherry red underneath

Dec 29, 2010 | 1990 Mitsubishi Mighty Max

1 Answer

I need to adjust the clutch on a 1995 standard mighty max mitsubishi I changed the clutch disc, pilot bearing, throw-out bearing and pressure plate, but the clutch stays against the fly wheel when running...


You will need to turn the cable adjuster so there is only about 1/8 inch of free travel of the cable where it attaches to throw out fork before it starts to move the fork. Once the throw out bearing is achieving its full travel the clutch should release and enable gear selection.

Don't forget to rate this post !!

Oct 11, 2010 | 1995 Mitsubishi Mighty Max

1 Answer

'95 Chevy S10 stuck in first gear


I think the shift linkage is all internal so if you can get the shifter pulled out of the top of the trans through the floor, you can probably realign the linkage to a neutral position and reinstall shifter.
There may be something worn or broken that caused it or just one of those fluke happenings.

Mar 20, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

91 Mitsubishi Mighty Max stalls during acceleration


Try changing your fuel filter, like on all fuel injection and electronic ignition problems the shade tree has to use the process of elimination. This is one of the cheapest.

Dec 14, 2008 | 1990 Mitsubishi Mighty Max

1 Answer

Carburator seems to stall at high rpm's


mcdevito75 here, It could be a bad gas filter or fuel pump, if you can, change them both.

Nov 30, 2008 | 1987 Mitsubishi Mighty Max

Not finding what you are looking for?
1990 Mitsubishi Mighty Max Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...