Question about 2001 Chrysler Concorde

1 Answer

Taking off the bumper

I was in a slight collision with another car. well long story short, i gotta take the bumper off and put it back on straight. Does anyone know what the best way to going about this is. I need to know where the bolts or clips are?? Please help!! Its just pushed in on one side and pulled out a little on the other side.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There are black buttons looking things that the middle pries out of under the hood right where the plastic bumber starts. BE VERY CAREFUL REMOVING THESE THEY WILL BREAK OFF IN A MINUTE!!!! Next u need to remove the front tires and support the car on jackstands. Then take a long (at least 24 inch) extension and remove the bolts holding the bumper on both sides now it should come off.

Posted on Jan 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a 2011 Edge collision sensor


First make sure the battery is disconnected to avoid blowing out your air bags. Next replace the offending collision sensor, it should be located on the radiator support, you may also need to remove the front bumper cover to gain access. If the vehicle was in a collision and that is the reason it's being replaced, then make sure you also check wiring for any damage as a short can cause the airbags to go off again unexpectedly and cause injury or damage to the vehicle.

After replacing the faulty part, clear the code(s) from the BCM.

Feb 04, 2014 | Ford Edge Cars & Trucks

1 Answer

Bumper of G6 pontiac


Be sure that your vehicle is outfitted with a reliable Pontiac G6 bumper in order to ascertain total safety on the street. A bumper absorbs a great deal of the hit to ensure that the safety pieces on your Pontiac G6 and the vehicle itself will not be damaged too much, if at all. Separate from harm reduction, bumpers are also made to help prevent accidents to pedestrians involved in any sort of wreck.
You are not going to require far more regarding durability since these Pontiac G6 bumpers are typically made to satisfy market requirements. In earlier times, bumpers had been bulky and cumbersome, though these days, Pontiac G6 bumpers are presently associated with the style of the vehicle. Basically, a Pontiac G6 won't be able to do without a bumper-not in case that you need to preserve the vehicle and remain safe in case you are involved in slight collisions. For extra decorative applications, decals can be used to improve the item's style.
There's only a lone online automotive component store that will offer you excellent Pontiac G6 bumper options. Here at Parts Train, you will locate merchandise made by dependable brands like APA/URO Parts, Body Armor, and Ranch Hand Truck Accessories. Our parts are obtainable at affordable prices to help give you outstanding value for your hard-earned money.

Jun 04, 2013 | Cars & Trucks

1 Answer

We have a 2004 60R withch has been great until a minor frontend, parking lot, collision a year ago.. the front bumper was replaced and the headlights have never worked well since. They point so far down...


Hello
Due to the collision a frame was damaged - that's why your headlamps are not lighting the road well. Try taking off the front bumper, headlamps, grill, fender and take a look for bended frame. I would take a hammer and bend the headlamp connections so that all the lamp turn a few degrees upwards. Then when you put everything back together - use your headlamp height regulator to make the beam light properly.
Hope this helps.

Jul 10, 2011 | Volvo S60 Cars & Trucks

1 Answer

We have a 2004 60R withch has been great until a minor frontend, parking lot, collision a year ago.. the fron bumper was replace4d and the headlights have never worked well since. They point so rar down...


NEED TO LET A BODY SHOP CHECK OUT FRONT UNIBODY STRUCTURE FOR DAMAGE WHEN YOU HAD A FRONT END COLLISION. IF FRONT STRUCTURE BEND OR DAMAGED. THE FRONT BUMPER AND HEADLIGHTS FRONT WHEEL ALIGNMENT GOING TO BE OFF.SOUND LIKE FRONT END COLLISION IMPACT DAMAGED THE FRONT UNIBODY STRUCTURE.

Jul 10, 2011 | 2004 Volvo S60

1 Answer

Replace rio rear brake light bulb


1. Behind each light you will see a small door in the back liner. Remove the 2 plugs in each door by pulling them straight out.

2. Gently pull back liner doors to expose rear of light assembly.

3. Remove three brass 10mm nuts from exposed bolts.

4. Slightly lift up bottom inside corner of light assembly, Pull back or sideways to center of bumper or trunk rear with wiggle movement to pull out rear light assembly. Takes a little while, but piece of cake.

5. Plug in the new bulb and put everything back in place.

Dec 07, 2010 | 2004 Kia Rio

1 Answer

Slight rear end collision has damaged back up sensors how do I trouble shoot the problem and how do I replace damaged sensors?


Sorry to hear about your collision. The sensors are mounted behind the bumper.If you look underneath you will see them and they should pop out i would start by making a visual inspection for obvious damged sensors and replace those.might have to pop them out and look closely start with ones that look like they took hardest hit. hope this helps let me know what you find and we can dig deeper if need to there is usually one or two that are obvious damaged

Nov 11, 2010 | 2005 Chevrolet Venture

1 Answer

1995 Mercury Villager that was in an accident - bumper sticks out


I would go to a pick N pull salavge yard and buy an entire used bumper assembly.

http://groups.yahoo.com/group/villagerquest/

Mar 29, 2010 | 1995 Mercury Villager

1 Answer

Someone backed into my 01 Ranger and the front bumper tilted, the back end down and the front end in to the underside of the grill with no damage to the grill and the bumper still looks straight how would...


first you have to remove the bumpers, if the reinforcement underneath needs to be pulled then do it, it you think the alignment is good enough then you can put the bumper back again. hope this helps

Feb 04, 2010 | 2001 Ford Ranger Regular Cab

3 Answers

Honda Odyssey collision repair


Depending on where you live, there prices are very good. Where I live, we can't find repairs for less than $78 per hour and body shops generally charge in the area of $120 per hour.

Sep 11, 2009 | 2003 Honda Odyssey

1 Answer

Cant get the tail light lense off my 07 tahoe.


Put a rag between the bottom of the tail light and the bumper so you dont scratch your paint. Remove the two screws that are visable and then grab the other side and pull straight out towards you (sometimes a slight **** is required). There are 2 body plugs that are holding it in on the side. The angle makes a difference, and be careful not to scratch the lens or bumper.

Jan 03, 2009 | 2007 Chevrolet Tahoe

Not finding what you are looking for?
2001 Chrysler Concorde Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...