How do i install the bulb in the headlamp - 2008 Chevrolet Equinox

Headlight Removal & Installation Bulb Replacement CAUTION
Improper handling of a halogen bulb could cause the bulb to shatter into flying glass fragments due to the bulbs containing gas under pressure. Always wear eye protection, only handle the bulb by its base, keep dirt and moisture off the bulb, do not install the bulb with power at the socket, and keep them away from children.

To Remove:

1. Turn off power to the headlamps.
2. Remove the headlamp assembly.
3. Turn the bulb socket counterclockwise and remove from the headlamp assembly.
4. Remove the bulb from the socket.

To Install:
NOTE: If oil from your skin or anything damp comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry. Too prevent the bulb from exploding when the bulb is turned on.

1. Install the bulb into the socket.
2. Install the bulb into the headlamp assembly and turn clockwise to lock into place.
3. Install the headlamp assembly.

Headlight Assembly To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Open the hood.
   
3. Remove the fasteners (D) that retain the headlamp assembly (C) to the headlamp bracket (A).
4. Pull the headlamp assembly (C) forward in order to disengage the rear retaining pin (B), and disconnect the electrical connector from the forward lamp harness.
5. Remove the headlamp assembly from the vehicle. NOTE: Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.
   
6. Remove the bulbs from the headlamp assembly by turning them counterclockwise.

To Install:

1. Install the bulbs into the headlamp assembly and turn them clockwise to lock in place.
2. Connect the electrical connector to the forward lamp harness.
3. Install the headlamp assembly (C) into the vehicle by pushing rearward in order to engage the rear retaining pin (B).
4. Install the fasteners (D) that retain the headlamp assembly (C) to the headlamp bracket (A).
5. Close the hood.

To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.

1. Turn the lamp switch to the off position.
   
2. Make sure the bulb is cool before changing.
   
3. Remove the headlamp assembly from the headlamp panel.
   
4. Remove the rear access cover from the headlamp assembly.
   
5. Disconnect the headlamp connector.
   
6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
   counterclockwise.

To Install:

1. Connect the headlamp connector.
   
2. Install the bulb into the headlamp assembly by rotating the bulb and socket
   clockwise.
   
3. Install the rear access cover onto the headlamp assembly.
   
4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)

1. Remove the grille from the front of the vehicle.
   
2. Release the headlamp assembly retaining tabs.
   
3. If equipped, disconnect the headlamp leveling motor connector.
   
4. Disconnect the headlamp connector.
   
5. Remove the park/turn and side marker bulb sockets from the headlamp
   assembly.
   
6. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
   
2. Install the park/turn and side marker bulb sockets into the headlamp
   assembly.
   
3. Connect the headlamp connector.
   
4. If equipped, connect the headlamp leveling motor connector.
   
5. Lock the headlamp assembly retaining tabs.
   
6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)

1. Release the headlamp assembly retaining tabs.
   
2. Disconnect the headlamp connector.
   
3. Remove the park/turn bulb socket from the headlamp assembly.
   
4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
   socket from the headlamp assembly.
   
5. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
   
2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
   socket into the headlamp assembly.
   
3. Install the park/turn bulb socket into the headlamp assembly.
   
4. Connect the headlamp connector.
   
5. Lock the headlamp assembly retaining tabs.

Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Headlamp Assembly Removal and Installation

1. WARNING: THE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HEADLAMP BULB AND RETAINER (13N021) ARE DROPPED. HANDLE BULB CAREFULLY. GRASP HEADLAMP BULB AND RETAINER ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HEADLAMP BULB AND RETAINER OUT OF REACH OF CHILDREN.
   NOTE: The headlamp (13008) on this vehicle does not need replacement when the headlamp bulb and retainer burns out. Refer to Headlamp Bulb for removal and installation of headlamp bulb and retainer .
   Position headlamp in the OFF position.

1. Remove headlamp dash panel junction wire (14290) from headlamp bulb and retainers by grasping wires firmly and carefully snapping connector downward.

1. NOTE: Use snap-ring pliers to spread headlamp mounting clips (13N129) , then pull straight upward to disengage.
   Remove three headlamp mounting clips attaching headlamp to radiator grille opening panel reinforcement (8A284) .

1. Remove headlamp from vehicle.

1. To install, reverse Removal procedure.

1. Aim headlamp .
   
   

REMOVAL PROCEDURE

1. Open the hood.
2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
3. Pull the headlamp assembly out and away from the vehicle
4. Disconnect the headlamp electrical connector.
5. Remove the headlamp assembly from the vehicle.
6. Remove the headlamp bulb cover from the headlamp assembly.
7. Remove the headlamp bulb socket from the headlamp assembly.

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Remove the headlamp bulb.
2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
3. Remove the side marker bulb.
4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
5. Remove the parking lamp bulb.

INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Install the headlamp bulb to the socket.
2. Install the headlamp bulb socket to the headlamp assembly.
3. Install the headlamp bulb cover to the headlamp assembly.
4. Install the side marker bulb to the socket.
5. Install the side marker bulb socket to the headlamp assembly.
6. Install the parking lamp bulb to the socket.
7. Install the parking lamp socket to the headlamp assembly.
8. Connect the headlamp electrical connector.
9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.

NOTE: Refer to Fastener Notice in Service Precautions.

1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

Tighten the bolts to 6 N.m (53 lb in).

1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
2. Close the hood.

Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.

1. Turn the lamp switch to the off position.
2. Make sure the bulb is cool before changing.
3. Remove the headlamp assembly from the headlamp panel.
4. Remove the rear access cover from the headlamp assembly.
5. Disconnect the headlamp connector.
6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.

To Install:

1. Connect the headlamp connector.
2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
3. Install the rear access cover onto the headlamp assembly.
4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly Chevrolet To Remove:
Headlamp Assembly (Chevrolet)

1. Remove the grille from the front of the vehicle.
2. Release the headlamp assembly retaining tabs.
3. If equipped, disconnect the headlamp leveling motor connector.
4. Disconnect the headlamp connector.
5. Remove the park/turn and side marker bulb sockets from the headlamp assembly.
6. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
2. Install the park/turn and side marker bulb sockets into the headlamp assembly.
3. Connect the headlamp connector.
4. If equipped, connect the headlamp leveling motor connector.
5. Lock the headlamp assembly retaining tabs.
6. Install the grille onto the front of the vehicle.

SECTION 417-01: Exterior Lighting 2007 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/10/2006 Headlamp Bulb Printable View (255 KB) Expedition Headlamp
Item Part Number Description 1 13006/13005 Headlamp assembly (LH/RH) 2 13N021 Headlamp bulb

Navigator High Intensity Discharge (HID) Headlamp Bulb
Item Part Number Description 1 13N019 HID bulb access cover 2 — HID bulb screws (2 required) (part of 13A006) 3 13N021 HID bulb 4 13A006 HID bulb electrical connector and harness Removal and Installation
WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp.
NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
All vehicles

1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly in this section.

Expedition

1. Rotate the headlamp bulb approximately 1/8 turn counterclockwise and remove the bulb from the headlamp assembly.

Navigator

1. Remove the HID bulb access cover.

1. Remove the 2 screws and the HID bulb.
   • Disconnect the electrical connector.

All vehicles

1. To install, reverse the removal procedure.

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb Printable View (327 KB) Freestyle, Five Hundred
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montego
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego

1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.

1. Remove the 6 screws and the headlamp bulb access cover.

Montego high beam bulb

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego HID bulb

1. Release the spring retainer and remove the HID bulb.
   • Disconnect the electrical connector.

All vehicles

1. To install, reverse the removal procedure.

I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.

SECTION 417-01: Exterior Lighting 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Bulb —Headlamp Removal

1. WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Grasp the bulb only by its base. Avoid touching the glass envelope.
   NOTE: The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp.
   NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Remove the headlamp bulb.
   1. Disconnect the electrical connector.
   1. Remove the headlamp bulb retainer by rotating it counterclockwise about one-eighth of a turn.
   1. Remove the headlamp bulb.

Installation

1. Install the headlamp bulb.
   1. Install the headlamp bulb.
   1. Install the headlamp bulb retainer by rotating it clockwise about one-eighth of a turn.
   1. Connect the electrical connector.

------
go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/