Question about 1998 Buick LeSabre

Open Question

Code B1015 Passenger loop resistance high

Location and procedure to remove the inflatable restraint instrument panel module.

Posted by on

1 Suggested Answer

lasvegasrich
  • 65 Answers

SOURCE: location of instr. panel control module 1998 buick

Under the right side of the IP, near the rear of the IP compartment
IP= Instrument Panel

Remove hush panel if you have to

Posted on Aug 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the airbag light to go off on a 2007 Chevy van Express


You need to find out what code or codes are stored in the airbag control module > There are a lot of components involved in your airbag system : If you haven't had any training on these systems your best bet is take it to a ASE certified repair shop . People have been killed messing with these systems not knowing what they were doing .
The frontal SIR system consists of the following components:
?€¢
AIR BAG indicator located on the instrument panel cluster (IPC)


?€¢
Driver and passenger knee bolsters


?€¢
Inflatable restraint front end sensor


?€¢
Inflatable restraint PASSENGER AIR BAG ON/OFF indicator located on the instrument panel


?€¢
Inflatable restraint Passenger Presence System (PPS)


?€¢
Inflatable restraint I/P module


?€¢
Inflatable restraint I/P module disable switch


?€¢
Inflatable restraint seat position sensors (SPS) (left/right)


?€¢
Inflatable restraint sensing and diagnostic module (SDM)


?€¢
Inflatable restraint steering wheel module


?€¢
Inflatable restraint steering wheel module coil


?€¢
Inflatable restraint wiring harnesses


?€¢
Seat belt pretensioners (left/right)


?€¢
Steering wheel and column

Nov 22, 2015 | Cars & Trucks

1 Answer

2000 CHEVY IMPALA AIR BAG LIGHT ON


  • B0041
CIRCUIT DESCRIPTION
The inflatable restraint side impact module-LF deployment loop consists of the inflatable restraint side impact module-LF, the inflatable restraint side impact module wiring harness, and the side impact module-LF high and low circuits. A shorting bar used within the side impact module-LF connector shorts together the side impact module-LF high and low circuits when the connector is disconnected. This helps to prevent unwanted deployment of the inflator module during servicing. During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) allows current to flow through the deployment loop in order to deploy the side impact module-LF. When the ignition is turned ON, the SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a Diagnostic Trouble Code (DTC) will be stored in memory.

CONDITIONS FOR RUNNING THE DTC
Ignition 1 voltage is within the normal operating voltage range.

CONDITIONS FOR SETTING THE DTC
  • DTC B0040 will set when the side impact module-LF deployment loop resistance is less than 1.3 ohms for 500 milliseconds .
  • DTC B0041 will set when one of the following conditions occurs:
  • Side impact module-LF high circuit is less than 2.4 volts and the side impact module-LF deployment loop is more than 6 ohms for 500 milliseconds .
  • Side impact module-LF deployment loop resistance is more than 4.8 ohms for 500 milliseconds .
  • DTC B0045 will set when one of the following conditions occur:
  • Side impact module-LF high and/or low circuits is short to ground or short to voltage for 500 milliseconds .
  • Side impact module-LF high circuit is less than 2.4 volts and side impact module-LF deployment loop resistance is less than 6 ohms for 500 milliseconds .
ACTION TAKEN WHEN THE DTC SETS
The SDM commands the AIR BAG indicator ON via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC
  • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
  • A history DTC will clear once 255 malfunction free ignition cycles have occurred.
DIAGNOSTIC AIDS
The following are possible causes of the malfunction:
  • A short between the side impact module-LF high and low circuits
  • An open or a high resistance in the side impact module-LF high or low circuits
  • A short to ground or a short to voltage in the side impact module-LF high or low circuits
  • The side impact module-LF connector
  • The SDM connector
  • A malfunctioning side impact module-LF
  • A malfunctioning SDM

Jan 29, 2013 | 2000 Chevrolet Impala

1 Answer

How do I remove the front soft cover/air bag on a 2003 Chevy Cavalier steering wheel to gain access to the horn components? Does this require a special tool?


Disarming the System

Print

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before performing many in-vehicle service procedures. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Turn the steering wheel so the vehicle's wheels are pointing straight-ahead.
  2. Turn the ignition switch to the LOCK position.
  3. Remove or disconnect the following:

    Ignition key AIR BAG fuse from the instrument panel fuse block Left-hand sound insulator Connector retainer and yellow 2-way connector at the base of the steering column. Right-hand sound insulator, if equipped with passenger side air bags Connector retainer and yellow 2-way connector from the passenger inflator module pigtail, if equipped with passenger side air bags

    0996b43f80208efb.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Driver-s side Yellow 2-way air bag connector retainer location

May 24, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

2009 chevy impala left front side deployment loop resistance B0014 above threshold


the following link covers yours reqest The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)
Models:2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)


This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

<A href="#ss1-2146754">
Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

<A href="#ss2-2146754">
Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

<A href="#ss3-2146754">
Diagnostic Information

DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.
<A href="#ss4-2146754">
Correction
DO THIS

Don't Do This

Test for proper connection/high resistance at connector C221 and/or C222.

DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.



Important:
The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column.
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.


  • <LI type=1>Remove the appropriate side door sill plate. <LI type=1>Remove the appropriate side hinge pillar panel. <LI type=1>Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222. <LI type=1>Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection. <LI type=1>Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times. <LI type=1>Clear the DTC and road test the vehicle. • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
    • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
    <LI type=1>Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229). <LI type=1>Road test the vehicle and confirm that the repair is complete. <LI type=1>Install the driver's side hinge pillar panel.
  • Install the driver's side door sill plate.
<A href="#ss5-2146754">
Parts Information
Part Number

Description

Qty

15306186

Connector (4-way Female, w/Leads)

1

88987998

Connector (4-way Male, w/Leads)

1 Service Airbag Have Codes Ask the GM Technician

May 01, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

What does air bag code 43 mean?


The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)


Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0043, (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)



Models:Tahoe

• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.

• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.

Apr 22, 2012 | 2003 Chevrolet Tahoe

1 Answer

How to Change an Ignition Lock on a 2004 Buick Rendezvous.


Please let me know if you have questions, and thanks for using FixYa.

Removal & Installation
  1. Disconnect the battery negative cable, as outlined in the Chassis Electrical Section.
  2. Disable the Inflatable Restraint (SIR) system. (see procedure below)
  3. Remove the steering wheel.
  4. Remove the tilt lever close out plate.
  5. Remove the retaining screw from the lower steering column trim covers.
  6. Tilt the trim cover down and slide rearward in order to disengage the locking tabs.
  7. Remove the lower steering column trim covers.
  8. Remove the retaining screws from the upper steering column trim cover.

    jturcotte_1886.gif

    Fig. Lift the trim cover in order to gain access to the lock cylinder access hole.

  9. Lift the trim cover in order to gain access to the lock cylinder access hole.
  10. Insert the Snap-On A173A bent-tip awl or equivalent, with a 3/32 in (2.5mm) tip, and 3/4 in (20mm) in length, into the access hole of the ignition lock cylinder.
  11. Turn the ignition lock cylinder to START .
  12. Use the bent tip in order to push down on the ignition lock cylinder retainer.
  13. Release the ignition lock cylinder to the RUN position.

    jturcotte_1887.gif

    Fig. Remove the ignition lock cylinder from the lock cylinder case.

  14. Remove the ignition lock cylinder from the lock cylinder case.

To install:
  1. Insert the ignition lock cylinder through the trim cover in the upper steering column.
  2. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
  3. Completely push the lock cylinder into the lock housing.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the retaining screws to the upper steering trim cover and tighten the screws to 31 inch lbs. (3.5 Nm).
  5. Match the tab slots on the lower trim cover with the locking tabs on the upper trim cover.
  6. Tilt the lower trim cover up and slide the lower trim cover until the locking tabs snap into the tab slots.
  7. Install the lower trim cover screws to the steering column and tighten the screws to 13 inch lbs. (1.5 Nm).
  8. Install the tilt lever close out plate.
  9. Install the steering wheel.
  10. Enable the SIR system, as outlined in the Chassis Electrical Section.
  11. Connect the battery negative cable.


Disarming the SIR System

Print

  1. Turn the wheels to the straight-ahead position, then turn the ignition switch to LOCK .
  2. Remove the console accessory wiring junction block access hole cover.
  3. Remove the "AIR BAG" or "SIR" fuse from the block, as applicable.
  4. Remove the left-hand sound insulator, for access to the SIR wiring harness.

    jturcotte_1888.gif

    Fig. Driver-s side air bag connector location


    jturcotte_1889.gif

    Fig. Passenger-s side air bag connector location


    jturcotte_1890.gif

    Fig. Side air bag connector location

  5. Remove the Connector Position Assurance (CPA) device, then disengage the yellow 2-way connector at the base of the steering column.
  6. Remove the right hand insulator panel.
  7. Remove the CPA from the inflatable restraint instrument panel module connector located behind the RH insulator panel.
  8. Disconnect the instrument panel module connector
  9. If equipped with side air bags, remove the CPA from the inflatable restraint side impact module-left front connector located under the driver seat.
  10. Disconnect the side impact module-left front connector.
  11. Remove the CPA from the inflatable restraint side impact module-right front connector located under the front passenger seat.
  12. Disconnect the side impact module-right front connector.
    NOTE With the fuse removed, the AIR BAG or SIR light will illuminate if the ignition switch is turned ON at any time. This is normal and does not indicate a problem when the system is disarmed.


Arming The SIR System
  1. Be sure the ignition is in the LOCK position.
  2. Connect the inflatable restraint side impact module-right front connector located under the front passenger seat.
  3. Install the CPA to the side impact module-right front connector.
  4. Connect the inflatable restraint side impact module-left front connector located under the driver seat.
  5. Install the CPA to the side impact module-left front connector.
  6. Engage the yellow SIR connector, then secure using the CPA device for both the drivers and passenger sides.
  7. Install the sound insulator panel.
  8. Install the SIR system fuse to the fuse block.
  9. Turn the ignition switch to the ON position and verify that the AIR BAG indicator light flashes 7 times, then extinguishes. If it does not go out, troubleshoot the SIR system fault.
  10. Install the instrument panel lower extension.

Jun 30, 2011 | 2004 Buick Rendezvous

1 Answer

Where is the airbag module located in the 2000 cadillac seville


Hello: Sir, There are a total of 5 (five) modules in the Inflatable restraint system, ( airbag) I will list them, their purpose and location:
Sensing & Diagnostic Module, the main module located under the rear of center console, Driver side inflator module located left side driver seat back . driver side inpact sensor located left lower side of center left pillar. steering wheel inflator module under the horn pad in the steering wheel. passenger front side inflator module located under righ side of upper instrument panel . Right front passenger side impact module right side of passenger seat lower back. Rf passenger side impact sensor. lower part of center pillar. The left and right sensors are not modules . Note, Codes B0051 and B0053 require replacement and programming with a scanner. Hope this helps you

Oct 08, 2010 | Cadillac Seville Cars & Trucks

2 Answers

2002 chevy truck.Code B0026


Hello and welcome. code B0026 is for a airbag malfunction. this code will require a high end scan tool, like a GM tech 2 scan tool to check out.this code is related to a deployment loop problem on the drivers side of vehicle

• DTC B0026 will set when one of the following conditions occurs:
- The SDM detects the steering wheel module deployment loop resistance is greater than 4.8 ? for 500 milliseconds. - The SDM detects the voltage at steering wheel module high signal is less than 2.4 volts and steering wheel module deployment loop resistance is 6 ? or greater for 500 milliseconds.The inflatable restraint steering wheel module deployment loop consists of a steering wheel module, steering wheel module coil, steering wheel module high signal circuit, and steering wheel module low signal circuit. Shorting bars are used on the steering wheel module connector as well as the steering wheel module coil connector which will short together the steering wheel module high and steering wheel module low signal circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

Sep 12, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

CODE B0026 HOW DO I RESOLVE? REAR DOOR LOCKS NOT WORKING, SERVICE BRAKE BOOSTER WARNING ON, AIRBAG LIGHT ON, SERVICE AIRBAG WIRNING, INTERMIT NO START. HELP MEEEE!!!!!!


The airbag connectors in behind the front kick panels have high resistance. The fix is to replace them. Here is TSB's

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:
Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)

Models:
2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)

This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

Diagnostic Information
DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.

Correction

DO THIS
Test for proper connection/high resistance at connector C221 and/or C222.

Don't Do This
DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

Important: The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column...
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.

1. Remove the appropriate side door sill plate.
2. Remove the appropriate side hinge pillar panel.
3. Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222.
4. Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection.
5. Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times.
6. Clear the DTC and road test the vehicle.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
7. Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229).
8. Road test the vehicle and confirm that the repair is complete.
9. Install the driver's side hinge pillar panel.
10. Install the driver's side door sill plate.

Parts Information
Part Number: 15306186
Description: Connector (4-way Female, w/Leads) - Qty 1

Part Number: 88987998
Description: Connector (4-way Male, w/Leads) - Qty 1


Hope this help (remember comment and rated this help).

May 07, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

Horn not working due to clock spring


The part is still available from GM. It is part # 94857236.

You must be careful when replacing the clock spring as it controls the SRS system.
You will need to remove the steering wheel airbag and and the steering wheel itself.

Important: Perform this procedure in order to prevent deployment of the air bags from the reserve energy supply power.

  1. Remove the CIG and IGN Fuses from the junction block (1), which is located near the base of the steering column.
  2. Remove the lower steering column trim cover.
  3. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  4. Remove the key from the ignition switch
  5. Release the inflatable restraint steering wheel module coil connector locking mechanism.
  6. Disconnect the inflatable restraint steering wheel module coil connector C3
  7. Remove the Instrument Panel (IP) compartment (2)
  8. Release then unlock the IP module connector (1).
  9. Disconnect the IP module pigtail.
  10. Release and unlock the driver and passenger seat module connectors.
  11. Disconnect the driver and passenger seat modules.42de416.gif0276398.gif6983629.gife094e58.gif

Jul 16, 2009 | 1998 Chevrolet Prizm

Not finding what you are looking for?
1998 Buick LeSabre Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...