Question about 1990 Buick LeSabre

1 Answer

HARMONIC BALANCER HOW TO TAKE IT OFF

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

Need a gear or pully puller. it is a device that has 2 curved arms with a bolt like device going through the middle. it is available at any auto parts store.

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 2006 dodge stratus.im changeing the front crank seal.do I have to pull the engine out to remove the harmonic balancer?


You should be able to get to the harmonic balancer while it's in the car. Remove right tire( use jack stands to hold the car up- not a jack). remove the inner splash guide and the balancer will be exposed. Using 3 jaw puller to remove harmonic balancer

Harmonic balancer removal DodgeForum com

May 31, 2014 | Cars & Trucks

1 Answer

Harmonic balancer


remove center bolts and with puller remove the harmonic balancer.then after,to replace install harmonic balancer and the center big bolt with air gun tight it until it sit

Aug 07, 2013 | Oldsmobile Delta 88 Cars & Trucks

1 Answer

The big outside pulley on the harmonic balancer fell off


The Harmonic balancer is held on to the front of the crank shaft with a bolt. there are pullys pressed onto the harmonic balancer in rubber.If more pulleys are needed for more accessories they are bolted to the harmonic balancer.

Apr 20, 2013 | Cars & Trucks

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on


the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

I need a how to to change harmonic balancer for 1995 nissan maxima. step by step


First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

Aug 26, 2009 | Nissan Maxima Cars & Trucks

2 Answers

Harmonic balancer


what are the steps to removing a harmonic balancers

Oct 18, 2008 | 1997 Chevrolet Corvette

Not finding what you are looking for?
1990 Buick LeSabre Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...