Question about 1984 Chrysler E-Class

1 Answer

Headlight switch how do i remove the headlight switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Is switch mounted on dash if so on back of switch there is a small button push it andpull the knob that you would turn head light on with out of switch the you will see nut that holds switch to to dash remove it and switch will fall out into your hands

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACE HEADLIGHT 2008 SPRINTER


On some cases there are few hidden clips holding the assembly from under hood,that has to be released to remove headlight .

There are few troubleshooting help links showing how to replace car headlights,i suggest you to refer the links to solve these issue.

--------
Click the link below:------
How to Replace a Headlight http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb


http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html


How to Replace a Park Light Assembly http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------
Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------
Headlight Assembly Removal On Honda Accord http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html --------------- Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html-----------
How to Replace a Headlight Door http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

---------
All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------
How to replace HID headlight bulbs for lexus 400h? http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------
Working of Headlight switch?
------------
Both headlight bulbs blow together?
------------
Car headlight bulbs don't last long?



----------------
These will help.
Thanks.

Nov 23, 2012 | 2010 Mercedes-Benz Sprinter

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

1 Answer

Both headlights quit working simotaneously


There are just (3) possible reasons for this:
(a) your headlight switch has failed, or
(b) your headlight relay has failed.
(c) Fuse 1 (25 Amps) has blown

The headlight relay and fuse 1 are located (I think) in a fuse/relay block under the hood.
The headlight switch is part of the "Multi-function Switch" on the steering column.

Here's how to replace the 2001 PT Cruiser multi-function switch:

archaeology_27.jpg
Multi-Function Switch Removal & Installation
1. Open the hood.
2. Disconnect and isolate the battery negative cable.
3. Remove both upper and lower steering column shrouds.
4. Disconnect both posi-lock harness connectors at the rear of the multi-function switch.
5. Remove multi-function switch mounting screws and remove switch from vehicle.




To Install the new multi-function switch:

Note:
If replacing the multi-function switch, the combination flasher and windshield wiper/washer switch
must be transferred to the new multi-function switch.

1. Remove the two Torx(R) screws retaining the wiper/washer switch, place next to the new
multi-function switch and install two screws.
2. Place switch into place and install mounting screws. Torque multi-function switch to column
retaining screws to 27 inch-lbs. (3 Nm).
3. Connect both posi-lock harness connectors at the rear of the multi-function switch.
4. Install both upper and lower steering column shrouds.
5. Connect the battery negative cable.
6. Close hood.
7. Verify vehicle and system operation.

Mar 15, 2011 | 2001 Chrysler PT Cruiser

1 Answer

The headlights doesn't turn on. already change bulbs.


Your headlight switch needs to be replaced. Here's the section from the maintenance manual.

Headlight Switch REMOVAL & INSTALLATION

1996 Dakota
  1. Disconnect the negative battery cable.
  2. Remove the steering column cover and remove the instrument panel bezel. Two screws are hidden behind the steering column cover.
  3. Remove the screws from the headlight switch bezel, pull the assembly out and disconnect the wiring.
  4. Remove the nut retaining the bezel to the bracket. Depress the spring button on the right side of the switch and remove the headlight switch knob and stem.
  5. Remove the spanner nut and remove the switch.
  6. The installation is the reverse of the removal procedure.

Feb 01, 2011 | 1996 Dodge Dakota

1 Answer

How do I remove halogen low beam head light to replace it?


Removal & Installation To Remove:
WARNING
The halogen fog light bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
NOTE: The headlight bulb should not be removed from the headlight assembly until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlight bulb performance. Contaminants may enter the headlight assembly where they can settle on the lens and reflector. Never turn on the headlights with the bulb removed.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: Make sure that the headlight switch and the ignition switch are in the OFF position.
  2. Remove the pin-type retainers, screws and the air deflector from the radiator.
  3. Remove the three bolts and the headlight assembly.
  4. Disconnect the electrical connector.
  5. Remove the cover from the rear of the headlight assembly.
  6. If equipped with HID, release the spring tabs to remove the low beam bulb, otherwise disconnect the electrical connector and remove the bulb.
  7. Disconnect the electrical connector and remove the high beam bulb.
HID low beam headlight bulb lin_tc_0085.gif

Standard low beam headlight bulb lin_tc_0086.gif

High beam headlight bulb lin_tc_0087.gif

To Install:
  1. Place the headlight assembly in the proper position.
  2. Install the cover from the rear of the headlight assembly.
  3. Connect the electrical connector.
  4. Install the three bolts and the headlight assembly.
  5. Install the radiator air deflector.
prev.gif next.gif

Dec 18, 2010 | 2003 Lincoln Town Car

1 Answer

Headlight swicht broke


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Remove the lower steering column cover-to-instrument panel screws and the cover.
  3. Remove the instrument cluster trim plate-to-instrument cluster screws and the panel, then allow the panel to hang to the left side by the wiring.
  4. Disconnect the electrical connector from the rear of the headlight switch.
  5. Disengage and remove the headlight switch from the instrument cluster trim plate.
To install:
  1. Connect the electrical connector to the rear of the headlight switch.
  2. Engage and install the headlight switch in the instrument cluster trim plate.
  3. Install the instrument cluster trim plate-to-instrument cluster screws and the panel.
  4. Install the lower steering column cover-to-instrument panel screws and the cover.
  5. Connect the negative battery cable to the battery and check operation.

Apr 27, 2010 | 1995 Chevrolet Astro

1 Answer

How do i replace my 2003 Buick Regal LS head light switch?


GM Lumina/Grand Prix/Cutlass Supreme/Regal 1988-1996 Headlight Switch - REMOVAL & INSTALLATION

Except With Head Up Display (HUD)
(see Figures 1, 2, 3 and 4)

4a4d6fd.jpg

Fig. 1: Headlight switch location and mounting-1988 Regal shown

5678262.jpg

Fig. 2: The headlight switch is secured with clips and screws-1990 Lumina shown

519a286.jpg

Fig. 3: Light switch location and attachment-1993 Cutlass Supreme

ef31eb5.jpg

Fig. 4: Headlight switch assembly-1996 vehicle shown
  1. Disconnect the negative battery cable.
  2. Remove the instrument cluster trim plate by unfastening the retaining screws or simply unsnapping it.
  3. If necessary, remove the air outlet trim plate. If may be secured with screws/bolts or clips.
  4. If accessible at this time, detach the switch electrical connector.
  5. Remove the switch, using one of the following procedures:
    1. Unfasten the retaining bolts/screws from the switch, then remove the switch from the instrument panel.
    2. Unsnap the headlight switch from the instrument panel.

  6. If not already done, detach the electrical connector from the switch at this time.

To install:
  1. Attach the switch electrical connector and fasten the switch to the instrument panel. If the switch is secured with screws, tighten to 18 inch lbs. (2 Nm).
  2. Install the air outlet and cluster trim plates.
  3. Connect the negative battery cable.

With Head Up Display (HUD)
(see Figure 5)

880af61.jpg

Fig. 5: The HUD incorporates the headlight, fog lamp and HUD switches
  1. Disconnect the negative battery cable.
  2. Remove the steering column opening filler panel.
  3. Remove the instrument cluster, as outlined earlier in this section.
  4. Depress the locking tabs, then pull the switch out.
  5. Detach the HUD electrical connectors.

To install:
  1. Attach the switch electrical connectors.
  2. Snap the switch securely into the instrument panel.
  3. Install the instrument cluster.
  4. Install the steering column opening filler panel.
  5. Connect the negative battery cable.
Hope this help (remember comment and rates this).

Apr 16, 2010 | 2003 Buick Regal

1 Answer

Headlight switch


REMOVAL & INSTALLATION
See Figures 1 and 2
  1. Disconnect the battery ground cable.
  2. On 1991-94 models, perform the following:
    1. Remove the ash tray assembly and the finish panel (snaps off).
    2. On the Explorer, remove the rear window wiper and heated backlite switch assembly (snaps out).
    3. On the Ranger, remove the storage bin (snaps out).
    4. Pull the headlight switch knob to the headlight on position. Depress the shaft release button and remove the knob and shaft assembly. 0900c1528018ef70.jpgFig. 1: View of the 1991-94 model headlight switch control knob release button
  3. On 1995-99 models, remove the instrument panel finish panel.
  4. Unscrew the mounting nut and remove the switch from the instrument panel, then remove the wiring connector from the switch.
0900c1528018ef71.jpgFig. 2: Exploded view of the 1995-99 model headlight switch componentsTo install:
  1. Connect the wiring connector to the headlamp switch, position the switch in the instrument panel and install the mounting nut.
  2. On 1995-99 models, install the instrument panel finish panel.
  3. On 1991-94 models, perform the following:
    1. Install the headlamp switch knob and shaft assembly by pushing the shaft into the switch until it locks into position.
    2. On the Explorer, install the rear window wiper and heated backlite switch assembly.
    3. On the Ranger, install the storage bin.
    4. Install the finish panel and the ash tray assembly.
  4. Connect the battery ground cable, and check the operation of the headlight switch.

Nov 29, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...