Question about 2006 Suzuki Vitara
Standing in front of car looking to the rear} un-plug bulb then rotate housing clockwise pull straight back and remove bulb then replace bulb and install in housing and rotate housing counter-clockwise always remember righty-tighty>lefty-loosey
Posted on Nov 15, 2008
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Feb 28, 2014 | 2004 Suzuki Grand Vitara
Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.
Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.
Grab the bulb and pull it from the socket with a slight wiggling motion.
Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.
Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.
Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.
Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed. Close the Galant's hood.
Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe
Close the Galant's hood.
Sep 27, 2012 | 2000 Mitsubishi Galant
Oct 21, 2010 | 2006 Chrysler Pacifica
Changing front, right turn signal on 2005 Buick Terraza:
Open hood; when facing the front of vehicle, the right turn signal is on the passenger
side (left). The headlight assembly
needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the
left side. Remove it. There is L-shaped pin on the right side of
the headlight assembly. Swing the pin counter-clockwise
(to the left). Pull the pin straight up
to remove. The headlight assembly is now
loose, but there is a pin snapped in a socket on the back of the assembly that
still holds the assembly. Pull the
headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held
just by the rubber gasket surrounding the assembly. You need to gently work the right side of the
gasket out of the grill cowling. The
assembly should pull straight out. The
wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and
pull out the light holder. Change the
bulb. Do not punch your man-card for
credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second
time. Once you have put the L-pin in
place, the screw back, and successfully tested the lights, you can now punch
I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.
Sep 07, 2010 | 2005 Buick Terraza
Aug 12, 2010 | 2006 Volkswagen Passat
Dec 28, 2009 | 2006 Dodge Grand Caravan
Jun 18, 2009 | 2002 Jeep Grand Cherokee
Jun 06, 2009 | 2006 Suzuki Grand Vitara
May 29, 2009 | 2006 Volkswagen Jetta
359 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: