Question about 2004 Chrysler Sebring

2 Answers



Posted by on

  • arthur j causey Oct 07, 2008

    has seprate coils per cylinder there are 2 motors offered for this vehical wire harness are different i swaped them the only difference i found was for were it hooks up to ecu the plug were different and the knock sensor were different the upper intake i used from the original motor when i talked to chrys parts they said that everything should inter change between the two motors they only listed one long block for this vehical the only life i get from this motor is a back fire every so often like the timing is off i have checked the crank sensor and its good it comands the fuel pump like its suppose to any other sugestions

  • arthur j causey Oct 09, 2008

    fly wheel was different from one motor to other change fly wheel car started up thankyou any way



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 200 questions.

  • Chrysler Expert
  • 254 Answers

The 2.7 engines are interchangeable but the flywheels and the front bank cam gears can be different. they have to be what the car came with or it wont run

Posted on Jan 05, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Expert
  • 69 Answers

Try seeing if the coil works here is how to see take a spark plug out and leave the wire connected place it on a metal part of the motor crank it over and have someone watch closely and see if the plugs spark on the metal if they don't then it needs a coil and/or coil wire replace just the coil wire first since that is the least expensive option if that does not solve it then change out the coil and dont hold or touch the coil wire when turning it over cause if it works it hurts like heck

Posted on Oct 07, 2008

  • 1 more comment 
  • Erick Beckwith Oct 07, 2008

    try making sure the timing is correct

  • Erick Beckwith Oct 08, 2008

    timing may be way off or even backwards

  • Erick Beckwith Oct 11, 2008

    knew it had to do with timing



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2004 sebring stalls and will not crank for hours it stalls while driveing or setting still

If it usually starts when cold, but when fails hot will not start until totally cold, suspect bad coil, ignition module or other electronic sensor on engine such as crank or cam sensor. Testing individual parts often is difficult, because part only fails when hot.

Oct 03, 2016 | 2004 Chrysler Sebring Touring

1 Answer

I have a 2006 chrysler sebring I just changed the camshaft and cranksensor and it still won't start it just cranks could it be the pcm ?

Chrysler Sebring no crank no start resolved - YouTube

? 1:11

Oct 21, 2013 - Uploaded by DanielRau1234
My car would not start. the problem turned out to be a 20 amp fuse. ... This fixed my 2006 Sebring. It's fuse ... My sons chrysler sebring 2004 has the exact same problem! .... Engine Won't Start - No Crank Diagnosis (Troubleshooting Starting System Issues) - Duration: 25:23. by Bushougoma 431,429 views.

Oct 27, 2015 | Chrysler Cars & Trucks

1 Answer

2004 Sebring replaced starter. OK for 2 days. No starting. Set for awhile, Started. Happened again. Computer said "NO BUS" . Local mechanics stumped. Help please??

Sounds like you may have a bad ignition switch. The ignition has be on to read codes and the ignition must be turned to crank a starter motor

Oct 22, 2013 | 2002 Chrysler Sebring

1 Answer

I have a 2001 sebring 2.7l v6 i have had the starter tested and it passed, just replaced the started fuse, fuel pump relay, and put in a rebuilt pmc unit and it still wont start. you can hear the fuel...

when installing a new chysler pcm you must have it programed by the dealer to learn your venicle by the vin number......butsound like you had the no start before the pcm did you check for fuel presure.......did you ckeck injector pulse....and did you ckeck for spark at coils thats where you should have started......

Jan 24, 2011 | 2004 Chrysler Sebring

1 Answer

The car does not start. The lights and the

check the fuseable links under the hood on the drivers side fender well you will find on that has blown into internally

Jan 21, 2010 | 2004 Chrysler Sebring

2 Answers

Where is the crankshaft postion sensor on a 2.7L 2003 sebring?

On the front of the motor at the bottom where the crank shaft comes out of the motor, the one with the largest pully, it will be mounted on the outside and has 3 or 4 wires going to it. If you remove and replace it make sure you get the correct air gap or it won't work.

Aug 18, 2009 | 2004 Chrysler Sebring

1 Answer

2004 sebring 2.7 engine, will strt when cold but not when warm

more than likely a bad crank sensor but not knowing if there are codes might also be a cam sensor,it is deffently a electrical componet problem hot soak of the motor will break down bad electrical sensors,

Jan 23, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides