Question about 1995 Jeep Grand Cherokee

1 Answer

Reply Getting a bit past the tools in my tool chest now. Will see what I can do on my own and with assistance from friendly neighbor who has a boatload of gadgets and tools. Again, thank you.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

Good luck

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The sizes of wenches and sockets or any special tools required to pull the starter off of a 84 mercury grand marquis v.8


Hi Troy:
Sounds as if you need the help of a buddy with a tool kit and some experience. It's a great learning experience.

May I suggest that before you start taking things apart, you get that experienced friend to assist in making sure that you have identified the problem that needs repair.

Oct 24, 2015 | Mercury Cars & Trucks

2 Answers

I keep getting a p0300 code on my jeep patriot 08 the codes willnot cleear and car is running fine . Is there a way to check the plug on coils any advice would be greatly appreciated.


Check your fuel pressure. A bad FP regulator or bad fuel pump/fuel pump wiring or fuel pump relay can give you random misfire problems.

Feb 20, 2015 | 2008 Jeep Patriot

1 Answer

Starter fluid worked


you need fuel line disconnect tools without tools you will damage fuel line connectors.

Nov 25, 2012 | 2000 Ford Explorer

1 Answer

Quick disconnect tool is not helpful on disconnecting fuel line from fuel filter on 92 F 150 w/4.9L


there are a few different tools and some work well and others just plain ****. Patience is the key sometimes with poor quality tools. If yo have the multi quick dis connect tool that is like the swiss army knife of quick disconnect tools, thats the worst one.
My neighbor had trouble with a quick disconnect fitting and came to get me. when I got in his garage he said "here's the tool." I threw it in the trash and came back to get my set of quick disconnects. It tool me longer to open the case, get the tool out and put it back than the time it took to undo the connection.

Jul 19, 2012 | Cars & Trucks

1 Answer

Bolt broke off in cranksaft how would i go about getting it out


Go to your local tool store or Sears and get a set of "easy outs".
Basically a reversed looking drill bit tool that grabs the broken section.
Good luck...

Jul 30, 2011 | Geo Tracker Cars & Trucks

2 Answers

I think my wheel bearing needs replaced in front driver side. could this be done in my driveway?


it depends on if it is a pressed bearing or not and if u need some heat to get it out i rec a shop.

Jan 26, 2011 | 2006 Buick Rainier

1 Answer

Engine will not crank. Battery is good Starter is good. When I turn the ignition nothing happens.i am not getting any power to close the starter solenoid. I can switch the vehicle on and use a jumper wire...


Be sure this car doesn't have a starter relay, you can can purchase a cd repair manual on ebay motors that has a electrical component locate in the software, this is a valuable tool to have, great deal for the $20.00. Hopefully this is not an ignition switch they are a pain to do you will need a steering wheel puller amongst other tools not commonly found in the laymans tool chest such as metric torx wrenches etc. check the replace the starter relay first if warranted then do the ignition switch be sure to check all fuses in the fuse block located in engine compartment if equipped.

Jun 23, 2010 | Cars & Trucks

1 Answer

Our right front strut is broke on our ford focus are they hard to change


hi from uk again !thank you for reply in my last reply assumtion ? that it is the coil spring on front suspension strut that has broken ?? ,my advice is if it is the coil spring broken ?? then i strongly advise you have it fixed ASAP! however? if whoever has told you ?the front strut is broke ? it is most probably the coil spring takes approx 1/2 hour to change with tools but here in uk coil springs cost approx £50 ? unfortunately as i am unaware your location ? i would gladly offer assistance if in uk but can only offer advice free ! therefor if you req further advice/info/assistance ? to DIY will be glad to help ! hope this helps and inspires you ? you can diy this ! being female or male the most important tool in any tool box is PATIENCE ! remember this ? mech's were not born with this knowledge the learn from experience/reading/ doing? so have a go and if you get stuck ? get in touch ? for free advice that what we are here for ?? best wishes from n/west uk lancashire

Jan 24, 2010 | 2000 Ford Focus

1 Answer

Where are the tools to remove the spare tire hidden?


they are either in a compartment on the tailgate or the right or left side trim panel in the back of the vehicle. instructions should be in tray with tools

Aug 23, 2009 | 1997 Lexus LX 450

2 Answers

Rear brakes


I think its too difficult you have a friend, family or neighbor that understand in those things? if not, take it to a mechanic, don't take risks, you'll be sorry for that, i been there and im sorry for what i done.

Jun 18, 2008 | 2007 Volkswagen Passat Sedan

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...