Question about Nissan Xterra

1 Answer

Intermitant problem with gears not going in on my 53 plate nissan terrano, have to turn ignition off before selecting gear

Posted by on

  • yadayada
    yadayada May 11, 2010

    Sounds like a clutch problem

×

1 Answer

New clutch fitted in feb

Posted on Oct 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem with my Nissan terrano 2 mechanical gearbox. It's hard to put to 1st gear. From 1'st to 2nd, 3rd, 4th, 5th, are also hard. Is it necessary to change clutch?


not a clutch problem unless you have just done a clutch kit change
more likely a hydraulic clutch problem ( air in the system) or master cylinder needing replacement .
if it is a cable operated clutch , replace the clutch

Dec 14, 2016 | Nissan Cars & Trucks

1 Answer

Nissan mistral auto 1998 losing power and sometimes stalls have to push red pin on gear shift lever to start.


The red pin on the gearshift lever is to allow selection of neutral in an emergency when the key is not in the ignition, because there is an interlock between the gearshift lever and the brake pedal. When you start the car normally you will hear the click of a relay when you stand on the brake to select any gear.
It sounds like there is a problem with the alignment of the lockout switch either on the gear lever or the switch or relay connected to the brake circuit.
get the codes read on the computer to give you some indication. I can't see how this has anything to do with the losing of power.
these vehicles have a reputation for problems with the eart straps from the engine, trans etc to the chassis. Remove and clean theses connection straps at both ends, and check their continuity with a meter, as sometimes they can break in the middle under the insulation from the vibration and movement of the components under braking and acceleration. Because the ECU depends on good electrical signals, and disturbance of the earth distorts the signal received.....

Mar 24, 2014 | 1999 Nissan Terrano

1 Answer

Nissan terrano 2 3.0L SVE loss of power under


Go and have the computer scanned for codes. Go from there, otherwise you are just firing the parts cannon at the problem.....

Sep 30, 2013 | 2005 Nissan Terrano 3.0

2 Answers

I have 1995 Nissan Terrano 4x4.Thishas an Automatic trans. It will not change gear.I have a power/hold button next to the hand brake.The power light flashes


If the power hold button switch On,It will stop the gear shifting & hold the gear position. or the problem with the system.

Feb 08, 2011 | Nissan Terrano Cars & Trucks

1 Answer

Terrano gearbox keeps jumping out of overdrive and


Nissan Terrano's have an Electronic Computer that controls the gearbox. It is hidden behind the left hand rear Speaker box, right hard up against the rear seat back rest. This system controls all functions regarding the gearbox and it's rev rates. If your vehicle is shifting back on long drives then it is possible that the computer sees any slight increase in revs as a desire to "Kickback" the gearbox to a lower gearing, hence it dropping out of overdrive. Unfortunately a gearbox specialist with a computer "Plug-in" is needed to fix this, but it is fixable. This problem should not be too expensive in comparison with a new gearbox.

Mar 16, 2010 | 1992 Nissan Pathfinder

1 Answer

98 nissan terrano, just fitted new clutch kit, and fully bled clutch. when engine is started wont go into gear. if engines off you can put it in and start it up. when you release the clutch it bites half...


are you sure u bled the clutch properly ? cant be any air in the line ! check fluid level in master cylinder and pull guts out of slave cylinder 2 make sure there are no leaks ( splits in the rubber ) other than that ur clutch fork may not be on the thrust bearing correctly !!!

Aug 26, 2009 | 1998 Nissan Pathfinder

2 Answers

Navara d22 on 53 plate missing at 2.500 r.pm and


i had a similar problem it turned out to be a neuteral selecter sensor located on the gear box

May 09, 2009 | 1997 Nissan Pickup

1 Answer

Nissan terrano accelerator button, whats it do??


this is the kick down for the auto trans it kicks back a gear on acceleration

Apr 13, 2009 | 1993 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...