Question about 2001 BMW 330

1 Answer

P0505 is it hard to replace the idle air speed control value on my bmw 330ci

Posted by on

  • Anonymous Mar 14, 2014

    How to replace gas door spring tentioner on 2005 bmw 330ci

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Your right it is hard. I usually leave the clamp on the hose to the idle vavle and pull it out with the throttle boot atatched. lossening the clamp on the throttle valve isnt easy. I actually have a long flexible driver to do that. you can use a 6 mm open wrench but it takes a few turns on the clamp.

Posted on Oct 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is code for P0505 2002 BMW 330ci


Do you understand what exactly sets a P0505? It is not an electrical code, it is purely performance. The code sets when it can't get the idle speed within +200 / -100 of the target for more than x seconds, and it takes a failure in two successive drive cycles to set the code. ANYTHING that can cause an incorrect idle speed can set this code. Vacuum leak, dirty IAC, etc.

Jan 27, 2015 | BMW Cars & Trucks

1 Answer

On 98 bmw 318i what causes code p1140 and po505


P0505 (Idle Control System Malfunction)
P1440 (Mass or Volume Air Flow Circuit Range/Performance )

May 16, 2014 | 1998 BMW 7 Series

1 Answer

2002 honda civic code p0505


Error Code: P0505
Fault Location:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle valve tight/sticking.
-Engine control module (ECM).

May 13, 2013 | Honda Civic Cars & Trucks

1 Answer

I just got my car scanned and a few codes pop up


Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .


Apr 30, 2013 | 2004 Honda Civic

1 Answer

1999 dodge durango 5.2l code po505


P0505 - Idle Control System Malfunctionxicon.jpghttp://engine-codes.com/p0505.htmlForum CodePossible causes- IACV-AAC valve harness is open or shorted
- IACV-AAC valve poor electrical connection
- Faulty IACV-AAC valve

Read more: http://engine-codes.com/p0505.html#ixzz1zVJIt34L

Jul 02, 2012 | 1999 Dodge Durango

1 Answer

Where is the IAC on my 2002 Toyota Echo?


The IAC is on the bottom of the throttle body and has a hole in the bottom of the throttle body that lets air into the IAC. YOu do not have to remove it, if you do remove it the throttle body would have to come off and a new gasket would be required. Usually spraying through with throttle body cleaner will clean the IAC so it functions properly.

About your P0505 faut code, The IAC (Idle Air Control) valve controls the idle speed of the engine. At idle the throttle plate is closed, of course. The IAC is computer controlled and allows only a certain amount of air around the throttle plate. This metered air controls the idle speed. The IAC has a "plunger" or "shutter" that moves to open or close the bypass air passageway. The more air the IAC allows around the throttle plate, the higher the idle. The PCM (Powertrain Control Module) uses the IAC valve to keep the idle speed correct with varying engine demands. Can be a three or four wire sensor depending on the model.
The PCM monitors voltages of the IAC circuits and if it detects an incorrect voltage on one or more of the IAC motor circuits it will set P0505. NOTE: Problems with the IAC would only be noticeable at idle or when throttle is closed.

Symptoms may include:MIL (Malfunction Indicator Lamp) illuminationEngine stalls and may not idle unless throttle is depressedIntermittently stalls when letting off the throttleEngine may idle too high

Potential causes of an P0505 code include:IAC motor connector is damaged (check connector and pins for damage, and moisture)One or more IAC circuits open or shorted to groundOne or more IAC circuits are shorted to voltageIAC has failedPCM has failed

Possible Solutions:This should be a fairly straightforward diagnosis. Start by clearing the fault codes. Then unplug the IAC and start the engine (This may cause other IAC codes to set. Just ignore them for now). If the P0505 code doesn't reset, replace the IAC. It is internally shorting one of the IAC circuits. If the code DOES return after unplugging the IAC and starting the engine, then you know it isn't the IAC motor. Visually check the wiring harness all the way back to the PCM. You may need to visually inspect the harness by removing all the insulation off the wires. It is possible that the wires could be shorting to eachother or to other wires in the harness.
If there are no wiring problems, and the code keeps returning with the IAC unplugged, you can check the PCM by removing the IAC wires from the PCM connector (or clipping the wires in a location where they can be repaired easily) and then start the engine (If you're not sure, don't do it. Take it to a qualified professional). Now if the code doesn't reset there is a problem with the wiring. Check for continuity on all the IAC wires. Any resistance points to a problem. Check for voltage on any(At this point there shouldn't be any voltages on the wires because they're clipped at one end and unplugged at the IAC). Repair as necessary. But if the P0505 code DOES reset after removing the IAC wires from the PCM connector(or clipping them), replace the PCM, there's a problem internally on the IAC control circuit.

Hope this helps.

Mar 28, 2012 | 2002 Toyota ECHO

1 Answer

P0505 IDLE AIR CONTROL SYSTEM\r\n1998 Toyota Land


replace the IAC valve to resolve this issue.

Jun 03, 2010 | 2003 Toyota Land Cruiser

Not finding what you are looking for?
2001 BMW 330 Logo

Related Topics:

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...