Question about 1993 Chevrolet Camaro

2 Answers

Replacing a starter

I'm replacing the starter on a 1993 camaro. I remove the bolts but cant get it out of the tight space. why do i have to remove to get it out

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you know there was a recall on the 1993's starters? Mine was at the dealer's repair shop for starting problems when they informed me. They replaced the starter.

Posted on Nov 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,035 Answers

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.
replacing a starter - 0900c152800b83b4.jpgFig. 2: Use a ratchet and socket extension to loosen ... Fig. 3: ... then remove the starter mounting bolts
  1. Making sure the note their positions, detach the electrical leads from the starter motor.
0900c152800b83b6.jpgFig. 4: Loosen the retainers, then remove the wiring from the starter
  1. Remove the starter motor from the vehicle.
0900c152800b83b7.jpgFig. 5: Carefully lower the starter motor from the vehicleTo install:
Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cabreplacing a starter - 5c28dd1.jpg. lbs. (15 Nm).5c28dd1.jpge527647.jpgec5c533.jpg

Posted on Oct 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a starter on a 1993 volvo 940 turbo. Is this a difficult task?


It looks easy for the 940 but I am not sure about the 940 turbo, as maybe some of the turbo parts are in the way. I'm not sure about that, since there is no documentation on the turbo model vs. the 940 standard model. If you can follow the following instructions, then I would give it a whirl.

REMOVAL & INSTALLATION - 1993 Volvo 940
  1. Disconnect the negative battery cable at the battery.
  2. Disconnect the leads from the starter motor.
  3. Remove the starter motor retaining bolts.
  4. Remove the starter motor from the vehicle. To install:
  5. Position the starter motor to the flywheel housing.
  6. Apply locking compound to the bolt threads and install the retaining bolts finger-tight.
  7. Tighten the bolts to approximately 25 ft. lbs. (34 Nm).
  8. Connect the starter motor leads and the negative battery cable. Fig. 1: Unfasten the nut retaining the starter cables . . . 90952p12.jpg
    Fig. 2: . . . and remove the starter cables 90952p14.jpg
    Fig. 3: Unfasten the starter retaining bolts . . . 90952p11.jpg
    Fig. 4: . . . and remove the starter from the engine 90952p15.jpg
prev.gif next.gif

Oct 28, 2010 | 1993 Volvo 940

1 Answer

How do i change the starter in my 1993 camero


disconnect the red terminal from battery. jack up car enough to get under. secure with jack stands. near rear of engine under car, is the starter. unplug electrical harness from starter. remove bolts. as you remove the bolts, starter will come down. remove, put new one in. put bolts in, tighten bolts. plug electricfal harness in to new starter. lower car from jack stands. connect red terminal to battery. if you have an alarm, put key in ignition to on position before connecting battery.

Sep 18, 2010 | 1993 Chevrolet Camaro

1 Answer

How to change the starter from my 1994 chevy camaro


REMOVAL & INSTALLATION 3.4L and 1993-95 5.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.


To install:

Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cable to 11 ft. lbs. (15 Nm).

Hope helps.

Sep 06, 2010 | 1994 Chevrolet Camaro

2 Answers

How do you take the starter out of a 1993 toyota four runner


The steps are given below:

1. Disconnect negative battery cable. Disconnect positive battery cable at the starter.
2. Disconnect remaining electrical connections at the starter soleniod.
3. Remove the nuts and or bolts holding the starterr to the bell housing and pull the starter towards the front of the vehicle.

Intallation in reverse, but make sure that the starter drive teeth are engaged with the flywheel teeth... You will have a very tight space in this job and you might need to modify some wrenches to do the job easier...

Feb 18, 2010 | 1993 Toyota 4Runner

2 Answers

How do I remove and replace a starter from a 1993 Toyota Previa? I am told it's rather difficult and may include removing something from the automatic transmission.


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front drive shaft.
  4. Remove the nut and disconnect the starter wire.
  5. Disconnect the starter connector.
  6. Remove the bolt holding the starter stay to the upper stiffener plate.
  7. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  8. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
To install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts.
  2. If equipped with 2WD, install the starter, nut and three bolts.
  3. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  4. Install the starter connector.
  5. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  6. If equipped with 4WD, install the front drive shaft.
  7. Connect the negative battery cable.
Good luck and this should take about 2 1/5 hours from start to finish and if you like, use lock tight medium strength to make sure the bolts don't go lose on you.

Nov 04, 2009 | 1991 Toyota Previa

2 Answers

How do I replace the starter on my 1993 chevy?


Disconnect the negative cable from the battery..
Under the front end - find the starter near where the trani connects to the motor and the really big gear (flywheel) is..
Undo 2 bolts to remove the starter.. take the wires off and be sure to put the wires on the starter the same way..
Connect the wires to the new starter and put the starter in with the to bolts.. The starter will only go in one way so you cant mess up how it goes in..

Good luck !

Sep 23, 2009 | 1993 Chevrolet K1500

1 Answer

Need to replace starter on a 1986 Camaro, but cannot get the old starter past the exhaust pipe.


Removing the starter
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect all wiring from the starter solenoid. Replace each nut as the connector is removed (as thread sizes differ from connector to connector). Note or tag the wiring positions for installation.
  4. Remove the bracket from the starter and the two mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.
  5. Remove the front bracket bolt or nut. Lower the starter front end first, and then remove the unit from the car.
These are the steps for removing the starter on the Camaro. Did you remove the bracket? Hope this helped and best wishes.

Aug 01, 2009 | 1986 Chevrolet Camaro

2 Answers

I need to replace the starter solenoid contacts on my 1993 Toyota pickup. The starter is located above the front differential on the right side and the space is very tight and I don't see how I can get my...


No, you do not technicaly need a jack or jack stands to change the starter. on the passenger side of the vehical, behind the tire there is an inspection cover that has 10mm bolts holding it in. pull those and then you can get to the starter easyer. i would remove the starter fo do what you are doing. Its still not fun. Good luck.

Apr 12, 2009 | 1993 Toyota Pickup

1 Answer

92 RS Camaro, Replaced battery and now car has no power?


are your battery post bolts clean and tight, my 89 rs ran fine untill i decided i wanted shiny new battery bolts, when i put them in and tightened them down my car had no power at all, i checked how tight they were, and they were TIGHT so i wiggled the black cable and re tightened it and bam my lights turned on, tryied starting it, and it started, sometimes you just gotta make sure the connection is really good, not just how tight it is, also check your ground wires, there are a few but the main 2 are located at the front pass side next to the batt, and on the back firewall going from the bottom pass head to the firewall, hope that helps, if not comment back

Mar 17, 2009 | 1992 Chevrolet Camaro

1 Answer

I have a grand marquis 1993 and the car wouldnt start although the batteries r good i was told by a mechanic it is the starter . I need to know can I replace the starter by myself and what do i need to do...


I would always suggest having a mechanic do things first and only try yourself if you think you can do it and you do not have the money for a mechanic that can give you a warranty.

Disconnect the battery cables in order to reduce the possibility of accidentally shocking yourself.

Remove the electrical connections from the side of the starter. There are usually two wires: a positive and a negative wire. Remove the positive wire first, and then remove the negative wire from the starter. You may want to mark the connections with a paint pen to help you correctly reconnect the connectors to their proper terminals. To remove the connections, you'll need to use an open face wrench or socket wrench to remove the bolts.
After both of the electrical connections are removed, you'll need to unbolt the starter from the chassis. Before you remove these bolts, take note of how the starter is oriented. You may want to mark the bolts with paint pens. There are usually only two or three bolts that attach the starter to the vehicle.

Remove the starter. In preparation, look closely at your car and determine what path will be easiest for removing the starter. It might be a tight fit, but you'll need to twist and pull the starter around various engine and frame parts in order to get it out of the car. Some cars may be particularly tight, especially those with front wheel drive. You may have to remove other parts in order to get enough space the pull the starter out. If you do remove engine parts, take care to remember their proper location. Replace bolts into the same place they came from once you pull a piece off. This will help you keep up with all of the pieces.

Once you've pulled the starter out, you can put the new starter in its place. You'll need to put it back in the exact same way you pulled the old starter out. Once you have it in place, put in a bolt just enough to hold the starter in place. Then connect the electrical connections beginning with the ground wire. Once the ground wire is connected, attach the rest of the wiring. Next, install the rest of the bolts holding the starter to the frame. Check to see that all bolts are tight.

Dec 18, 2008 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
1993 Chevrolet Camaro Logo

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...