Question about Mitsubishi Lancer

Open Question

I have 97 magna executive and whenever i start there are two warning lamp blinking on speedometer one is red about speed belt and other is engine indication lamp both goes off in 4-5 seconds but today engine indication lamp stays on and i am not able to start my car i dont know wht to do as going to dealer will cost me fortunes so can you please help me out, i have also tried with other spare keys but the light still stays on so i am not able to start engine everything else is working but i dont know wht to do so please relply or call me 0061430141490.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Red blinking warning light beside clock in center of dash. What is it?

This is the factory installed "Security" light. It blinks to let you know that the security system is active, and to ward off potential theives. It's part of the factory anti-theft system. Also, it is a diode, and consumes virtually no battery power.
Normal condition; nothing to worry about.

Posted on Oct 15, 2008

Ad
  • 8 Answers

SOURCE: Can't find the transmission drain plug?

Should be on the side of the trans, or on the trans sump. Hope this helps

Posted on May 05, 2009

  • 3 Answers

SOURCE: 2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low

yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

Posted on May 12, 2009

  • 6 Answers

SOURCE: '97 GMC Jimmy: engine turns over but car won't start, electrical?

Sounds like a bad ignition switch but could also be a bad connection to the ICP or just a plain old bad ICP (Instrument control panel). The ICP needs to be able to communicate with the ECM, Brake Control Module and the SDM (sensing and diagnostic module). If these can not "talk" to each other the vehicle will go into a lock out theft mode...assuming it has a factory VAT system. But I would bet on the ignition switch first...seen it many times.

Posted on Feb 09, 2010

Testimonial: "Thank you very much. It will be very helpful to have an idea when I talk to the shop of what it might be so I can compare costs and won't look stupid."

  • 1 Answer

SOURCE: Malfunction Indicator Lamp(MIL) on and car shakes

Sounds like your o2 sensors are screwed up. there are 2 o2 sensors on the 1.8t (one before the catalytic converter and one after). The computer on your car uses data from the sensors to adjust the fuel mixture for your car. It sounds like it's running too rich which can cause detonation inside the piston. This is VERY bad for your pistons. Take it in to the shop and get OEM o2 sensors. Don't buy anything aftermarket.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

7 dings and a beep when starting 2000 ford explorer? what does that mean


NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with a scan tool.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition - Continuous Chime, 120/Min. 740 Hz Headlamps On - Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) - 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.

Feb 12, 2015 | 2000 Ford Explorer Eddie Bauer

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

How many indicator lights are there and where are they for 2009 f150 supercrew


29f0320.gif

Item Part Number Description 1 — Tachometer 2 — LH turn indicator 3 — Oil pressure gauge 4 — Overdrive (O/D) off/tow haul indicator 5 — Engine temperature gauge 6 — Air bag warning indicator 7 — Safety belt warning indicator 8 — Fuel gauge 9 — Tire Pressure Monitoring System (TPMS) warning indicator 10 — Speed control indicator 11 — Transmission temperature gauge 12 — RH turn indicator 13 — Speedometer 14 — Malfunction Indicator Lamp (MIL) 15 — Message center indicator display area 16 — High beam indicator 17 — ABS warning indicator 18 — Brake warning indicator 19 — Message center display area 20 — Anti-theft indicator

Feb 27, 2010 | 2009 Ford F-150

1 Answer

Warning bell won't stop sounding


Section 13-09: Gauges, Warning Devices — Chime System 1996 Windstar Workshop Manual
DESCRIPTION AND OPERATION Warning Chime Systems Three distinct sounds are used to indicate the area of concern. Seat belt warning generates 1 chime per second
key-in-ignition generates 2 chimes per second
headlight on generates 4 chimes per second.
Key-In-Ignition Warning The key-in-ignition warning will sound when the driver's front door (20125) is opened with the key in the ignition switch. It will continue to sound until the key is removed, the front door is closed, the ignition switch is turned to START or the vehicle speed is over 24 kmh (15 mph).

Safety Belt Warning When the ignition switch is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
  • The safety belt warning indicator lamp (10C859) will activate for 60 seconds or until the driver's safety belt is fastened. Both the chime and lamp activate at the same time.
Anytime the ignition switch is released from START and returns to RUN while the safety belt lamp or chime is activated, the safety belt warning lamp or chime will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Headlamp Switch On Warning The chime will be activated if the headlamps or parking lamps are ON, the key is not in the ignition and the driver's door is opened. The chime will sound at a rate of four per second.

Apr 23, 2009 | 1996 Ford Windstar

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

3 Answers

1995 Buick Lesabre Speedo inop


It may be a faulty speedometer with a short inside, or a short on speedometer wirings or connector.

Whenever car vibration cause the wiring to short, there you lose speedometer and trans functionality.

You need to access the speedometer connector and wirings to
instrument panel to fix this.

Feb 01, 2009 | 1995 Buick LeSabre

1 Answer

Diagnostic light blinking 17 times means what ?


i had the same problem, it should be the speed sensor on your transmisson after a while your speedometer will stop working. no clue on the lamp...

Dec 29, 2008 | 1989 Honda Prelude

2 Answers

Speed sensor and overdrive


OVERDRIVE ENGAGEMENT IS TIED TO THE SPEED SENSOR SIGNAL, THE SYSTEM WILL NOT GO INTO OD UNTIL THE CAR REACHES A CERTAIN SPEED, IN MOST CASES AROUND 35-40 MPH, THE SPEED SENSOR SIGNAL TELLS THE ECU WHEN THE CORRECT SPEED HAS BEEN REACHED.

Oct 01, 2008 | 1991 Honda Accord

1 Answer

1989 Mercury Tracer Sta. Wgn.


your owner manaul has it. your fuse cover should have chart too.

here is 96 tracer. You also have main fuses under hood.

INTERIOR FUSE JUNCTION PANEL REFERENCE CHART Fuse Fuse Rating Color Protected Components (REAR WIPER) 10A Red Rear wiper and washer motors, heater and A/C relays, daytime running lamps control (Canada), climate control assembly panel illumination HAZARD 15A Blue Front and rear turn signal lamps, turn signal indicator lamp, indicator flasher ROOM 10A (1.9L)
15A (1.8L) Red
Blue Dome and map lamps, safety belt warning chime, ignition key illumination, luggage compartment lamp, vanity mirror lamp, radio chassis (memory), power door lock relay, shift interlock system, powertrain control module (PCM), radio amplifier (memory) ENGINE 15A Blue Fan control (FC) relays, PCM relay RADIO 15A Blue Radio chassis, radio amplifier, remote control mirror, instrument panel illumination (DOOR LOCK) 30A Light Green Power door lock actuators BELT 30A Light Green Passive restraint control module, passive restraint motors (POWER WINDOW) 30A Light Green Window regulator electric drives METER 15A Blue Instrument cluster, backup lamps, rear lamps, speed control system, shift interlock system, safety belt warning chime, passive restraint control module, hazard flasher, PCM (1.8L Canada) WIPER 20A Yellow Windshield wiper motor and windshield washer pump STOP 20A Yellow Stoplamp, horn (1.9L only), rear hi-mount lamp TAIL 15A Blue Parking lamps, cornering lamps, rear lamps, license lamps, compartment lamp, instrument panel illumination (SUN ROOF) 15A Blue Sliding roof panel motor ABS 10A Red Anti-lock brake system (ABS) (1.8L only) (DEFOG) 20A Yellow Rear window defroster HEATER 30A
circuit breaker — A/C blower motor HO2S
(ON INTERIOR FUSE JUNCTION PANEL SIDE) 10A (1.9L)
20A (1.8L) Red
Yellow Heated oxygen sensor (HO2S) CIGAR
(ON INTERIOR FUSE JUNCTION PANEL SIDE) 20A Yellow Cigar lighter knob and element CIGAR 20A Yellow Cigar lighter OBD II 10A Red Data link connector #2 BLOWER 30A Light Green Blower motor relay HORN 20A Yellow Horn (1.8L only)

Aug 10, 2008 | 1989 Mercury Tracer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...