Question about Toyota Avalon

Open Question

Toyota dealer diagnosed "check engine" light as trouble codes P1411 and P0402, and recommends replacing ERG Valve and Position Sensor. Assuming the diaphram is good, can I clean the valve, and then replace the position sensor? There are 6 bolts than attach the valve body. 4 are easy access, but the bottom 2 are hard to reach. They are attached by a 10MM hex nut with a threaded shaft down the middle. When I turn the nut, will the shaft turn with it? Or is the nut a pal nut, and after removal, I will somehow have to get on the end of the shaft to remove it?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: PO171 OBD-II Trouble Code " System Lean To Bank 1

Check PCV valve and be sure it is not stuck open.  Check for vacuum leak at intake manifold.  

Posted on Jan 01, 2009

  • 412 Answers

SOURCE: Error Code 406 EGR Positions Sensor

yes it is..you need to replace egr valve assembly..make sure you disconnect battery while replacing..some times fault will return even after replacing valve..

Posted on May 23, 2009

  • 1 Answer

SOURCE: 2005 Dodge Stratus ? Camshaft Position Sensor causing problems (I

I had the same problem with my '05 Stratus SXT 2.4 DOHC. I've replaced the cam pos sensor and it seems to be running fine right now. On the Dodge forums a lot of the guys say that you need to replace the crank pos sensor too. I've bought one of those just in case it comes back again. Hope this helps.

Posted on Jun 24, 2009

polarcycle
  • 1392 Answers

SOURCE: 2002 Ford Escape (V6) P0401 P0402 nightmare

Sounds like you have a vacuum leak, a problem with the wiring, or a bad PCM. Check wiring for pinched, chafed, pierced, or broken wires. Make sure vacuum supply is good, and not collapsing when the vehicle is running. Beyond that, a trip to the dealer may be in order.

Posted on Jul 22, 2009

  • 38 Answers

SOURCE: 1989 Chevrolet C1500 with 5.7L V-8. Engine dies

fuel pump is working but when accelerating it doesnt pump enough fuel up to the engine then it will fall on its face if it is a electric pump you may have to drop the tank if it is inside and replace it if it is on the engine replace it thats what is exactly wrong with it

Posted on Jul 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I Fix the code P1410 by replaced the EGR position sensor. Now, I the code P402 is on, what should I do to fix this code?


Erg is acting up sometime you can clean the carbon out the valve
amd the sensor needs look also follow tjhe hose to it
egr position sensor may need replaced ck for any leaks

Sep 26, 2014 | 1998 Toyota Camry

1 Answer

Please GeoffW1 this are the fualt code diagnose from my toyota camry 1999 model v6 engine FAULT NUMBERS- 1.( p0110 ) 2.( p0135) 3.(p0450) 4.( p1410) 5.(P1411) please i need their locations and...


Sorry, I never noticed this post, for some reason I did not get an email from Fixya. If it is not too late..........
p0110 is the Intake Air Temp sensor or its wiring connector at fault. This is located at the side of the air cleaner housing.
p0135 is a fault in the No 1 oxygen sensor in bank 1, or its wiring connector. This thing is located in the exhaust manifold under the sheet metal shield at the front of the engine
p0450 is an evaporative emission system pressure sensor fault. Many people recommend replacing the fuel filler cap gasket before going further with this one

http://repairpal.com/OBD-II-Code-P0450



p1410 and p1411 indicate an EGR valve malfunction, and it may be enough to simply clean and check it, located on the engine next to the firewall. Also check the vacuum modulator and Vacuum Switch Valve, as shown here p46, 146, 152, 190


http://www.turboninjas.com/camry/eg1.pdf

Nov 15, 2012 | 1999 Toyota Camry

1 Answer

2005 magnum p0406 egr valve sensor code error


P0406 indicates high voltage on the EGR sensor circuit. this is recommended for every 30,000 miles be inspected. although EGR system do not requires periodic inspection. instead, check only if engine trouble's develop. most EGR's requires replacing EGR valve, cleaning passages and installing new vacuum hose. misrouted vacuum hose causes engine poor operation. so. not just to unplug it.

Aug 20, 2012 | 2005 Dodge Magnum

1 Answer

402 code emision light on


Hi there:

DTC P0402 - Exhaust Gas Recirculation Flow (EGR) Excessive Detected

EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor (DPF). These things work together to deliver the correct amount of recirculation based on engine temperature, load, etc. The P0402 code means that OBD detected an excessive amount of EGR.


Symptoms

You may notice drivability problems such as the engine may surge off idle. There may also be other symptoms.


Causes

A code P0402 most likely means one or more of the following has happened:

  • The DPFE (differential pressure) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (most likely carbon buildup)
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions

With a P0402, it is common for people to replace the EGR valve, only to have the problem return. The most likely solution is to replace the DPFE sensor.

  • Check the voltage at the DPFE sensor both at idle and when the EGR is open
  • Replace the DPFE sensor


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 16, 2012 | Toyota Cars & Trucks

2 Answers

Service engine code P0402 for Ford Mustang


P0402 OBD-II Trouble Code - Exhaust Gas Recirculation Flow (EGR) Excessive Detected

What does that mean?
EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor (DPF). These things work together to deliver the correct amount of recirculation based on engine temperature, load, etc. The P0402 code means that OBD detected an excessive amount of EGR.

Symptoms
You may notice drivability problems such as the engine may surge off idle. There may also be other symptoms.

Causes
A code P0402 most likely means one or more of the following has happened:
* The DPFE (differential pressure) sensor is faulty and needs to be replaced
* There is a blockage in the EGR (most likely carbon buildup)
* The EGR valve is faulty
* The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions
With a P0402, it is common for people to replace the EGR valve, only to have the problem return. The most likely solution is to replace the DPFE sensor.
* Check the voltage at the DPFE sensor both at idle and when the EGR is open
* Replace the DPFE sensor

Hope helps (remember rated and comment this).

May 27, 2010 | 2001 Ford Mustang

1 Answer

I have problem with code 1126 (toyota 4 runner 2001


Manufacturer Specific Codes

P1100
BARO Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1120 Accelerator Pedal Position Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1121 Accelerator Pedal Position Sensor Range/Performance Problem

P1125 Throttle Control Motor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1126 Magnetic Clutch Circuit

P1127 ETCS Actuator Power Source Circuit

P1128 Throttle Control Motor Lock

P1129 Electric Throttle Control System

P1130 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1133 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1135 Air/Fuel Sensor Heater Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1150 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 2)

P1153 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 2) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1155 Air/Fuel Sensor Heater Circuit. (Bank 1 Sensor 2)

P1200 Fuel Pump Relay Circuit

P1300 Igniter Circuit Malfunction - No. 1

P1305 Igniter Circuit Malfunction - No. 2

P1335 No Crankshaft Position Sensor Signal - Engine Running

P1349 VVT System

P1400 Sub-Throttle Position Sensor

P1401 Sub-Throttle Position Sensor Range/Performance Problem

P1405 Turbo Pressure Sensor Circuit

P1406 Turbo Pressure Sensor Range/Performance Problem

P1410 EGR Valve Position Sensor Circuit Malfunction - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1411 EGR Valve Position Sensor Circuit Range/Performance - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1500 Starter Signal Circuit

P1510 Boost Pressure Control Circuit

P1511 Boost Pressure Low

P1512 Boost Pressure High

P1520 Stop Lamp Switch Signal Malfunction

P1565 Cruise Control Main Switch Circuit

P1600 ECM BATT Malfunction

P1605 Knock Control CPU

P1630 Traction Control System

P1633 ECM

P1652 Idle Air Control Valve Control Circuit

P1656 OCV Circuit

P1658 Wastegate Valve Control Circuit

P1661 EGR Circuit

P1662 EGR Bypass Valve Control Circuit

P1700 Vehicle Speed Sensor '2' Circuit Fault

P1705 Direct Clutch Speed Circuit Fault

P1765 Linear Shift Solenoid Circuit Fault

P1780 Park/Neutral Position Switch Malfunction (Only For A/T)

Back To Top Of Toyota Check Engine Light Codes Page

Mar 21, 2009 | 2002 Toyota 4Runner

2 Answers

2000 toyota camry v6 code p0402


The egr valve on that motor has a egr positioning sensor mounted on top. The sensor goes bad and the ecu can't determine the how far the valve is opening so it opens it too much. This causes surging of the engine under light throttle application. Also as stated above the egr can stick causing rough idle. Either way if you get the valve from the dealer it will come with the sensor solving both your problems.

Dec 23, 2008 | 2000 Toyota Camry

1 Answer

P0402 code


follow the vaccum line from the egr valve back to the silinoid that silinoid is defective or unplugged. the egr valve is below the breater tube on the back side of the engine

Aug 14, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...