Question about 2006 Scion tC

1 Answer

Steering wheel trim removal

I have a '06' Scion tC. I want to remove the two silver pieces of trim on the front of my steering wheel, that are on either side of my horn button.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Scion Master
  • 827 Answers

Why? need to remove the steering wheel to get to holders

Posted on Nov 30, 2013

6 Suggested Answers

  • 345 Answers

SOURCE: horn press panel on steering wheel

remove the airbag !!! but disconnect the battery first and leave it for 10mins or so every thing is behind the airbag.

Posted on Dec 30, 2008

  • 140 Answers

SOURCE: How do I reset the check engine light for a 2006 scion tc?

YOU CAN GO TO ANY ADVANDED AUTO PARTS AND THEY CAN HOOK UP A OBD2 SCANNER, WE THEY DO ASK THEM TO RESET THE LIGHT FOR YOU.. THIS IS A FREE SERVICE TO THE PUBLIC..GOOD LUCK KEITH..

Posted on Mar 14, 2009

  • 1 Answer

SOURCE: How to remove trim piece around radio in Scion XA?

http://www.installer.com/pdf/99-8209.pdf

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: how to reset low tire pressure on a 06 scion

you have to turn the key to 'on' first. if the light comes on, push the reset button to turn it off. push and hold the reset switch until the light blinks 3 times. the system will be reset in about an hour if the vehicle speed is between 31-62mph, the roads are dry smooth and straight, and the number of passengers is 1 or 2.

Posted on Aug 18, 2009

  • 1 Answer

SOURCE: How to remove front stabilizer bar in '05 Scion TC

I don't know if you can get the bushings out without changing the bar or not, but changing the bar is a big job for a DIY. I was thinking about it but will probably have a pro do it for me. From the shop manual: 1. PLACE FRONT WHEEL FACING STRAIGHT AHEAD 2. REMOVE COLUMN HOLE COVER SILENCER SHEET (See page SR-9) 3. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (See page PS-21) 4. DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY 5. REMOVE FRONT WHEEL 6. REMOVE ENGINE UNDER COVER LH 7. REMOVE ENGINE UNDER COVER RH 8. REMOVE FRONT STABILIZER LINK ASSEMBLY LH (a) Remove the 2 nuts and front stabilizer link LH. HINT: Use a 6 mm hexagon wrench to hold the stud if the ball joint turns together with the nut. 9. REMOVE FRONT STABILIZER LINK ASSEMBLY RH HINT: Use the same procedures described for the LH side. 10. DISCONNECT TIE ROD END SUB-ASSEMBLY LH (See page DS-6) 11. DISCONNECT TIE ROD END SUB-ASSEMBLY RH (See page PS-21) 12. DISCONNECT PRESSURE FEED TUBE ASSEMBLY (See page PS-21) 13. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH (See page SP-22) 14. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH HINT: Use the same procedures described for the LH side. 15. REMOVE FRONT FLOOR PANEL BRACE (See page EX-2) 16. REMOVE CENTER EXHAUST PIPE ASSEMBLY (See page EX-2) 17. REMOVE HOOD SUB-ASSEMBLY 18. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY 19. SUSPEND ENGINE ASSEMBLY (See page MX-19) 20. REMOVE NO. 1 HOOK (See page PS-22) 21. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (See page PS-22) 22. REMOVE FRONT NO. 1 STABILIZER BRACKET LH (a) Remove the 2 bolts and front No. 1 stabilizer bracket LH from the suspension crossmember. 23. REMOVE FRONT NO. 1 STABILIZER BRACKET RH HINT: Use the same procedures described for the LH side. 24. REMOVE FRONT NO. 1 STABILIZER BAR BUSH (a) Remove the 2 No. 1 stabilizer bar bushes from the stabilizer bar. 25. REMOVE FRONT STABILIZER BAR
You can download the manual online for about $15. Well worth it.

Posted on Sep 08, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Piece that holds the bulb fell how do i remove the overhead console


first are you talking about the front light inside or the rear light, i dont have a over head consol, does not your tc have a sun roof?

Oct 18, 2013 | 2007 Scion tC Coupe

1 Answer

How to remove front glass panel on panoramic roof 2007 scion tc


go on line to sciontc.com and type ion this it should bring up how to remove it

Nov 30, 2012 | 2007 Scion tC Coupe

1 Answer

2005 scion tc steering gear lights out how do I replace


my 07 is in the dash below the tach, so you will need to remove the cluster to be able to install a new lamp

Sep 06, 2012 | 2005 Scion tC

1 Answer

How to replace a front wheel bearing on a 2006 scion tc


you need to remove wheel, you will need to remove the caliper and caliper holder, 3 bolts on bottom of the ball joint, 2 bolts holding shock tube, need to unbend the indent on the axle nut, then you need a socket that will fit the nut, remove the nut, there will be a ball joint, with a cotter pin in it, take it out and loosen nut don't take it off all the way, with nut on hit with a hammer, it will loosen up then take off the nut, this will allow the whole assembly to come off axle, then you take the assembly to a shop that will press out the old bearing and put the new one in, I suggest doing both, even if only one is making a grinding noise, after all is done and new ones are in reverse the way you took off

Apr 22, 2012 | Scion TC Cars & Trucks

1 Answer

How to remove front glass panel of sunroof on a 2005 Scion tc?


sun roof is all one so you have to remove it, by taking all inside roof panels

Feb 24, 2011 | 2009 Scion tC

1 Answer

1984 pontiac parisienne how to replace ignition switch


The ignition switch is on top of the steering column. You will have to remove the trim piece under the steering column and then loose the 2 bolts (1/2 inch) that holds the steering column. Watch your shift ind if it starts to move you will have to unhook ( silver or black clip with a small cable attached to it). Make sure you unhook the battery and block the wheels to keep the car from rolling. The switch uses the same bolts and the dimmer switch. Remove old switch and install new switch.

Oct 20, 2010 | 1984 Pontiac Parisienne

1 Answer

After you have taken off the rotor how do you remove the front axle hub assembly?


there is a little more to do before you can, ball joint for steering arm, remove 3 bolts on bottom of hub, 2 bolts on shock, and wheel nut this is a choir in its self, I take it that you want to replace the bearings, you will need to have a press to do this.

Aug 03, 2010 | 2005 Scion tC

2 Answers

Trunk trouble


Mine broke too. I have read that this is pretty common in this car...i think Scion needs to seriously take a look at this problem and come up with a solution.

Feb 24, 2010 | 2005 Scion tC

1 Answer

How to remove front stabilizer bar in '05 Scion TC


I don't know if you can get the bushings out without changing the bar or not, but changing the bar is a big job for a DIY. I was thinking about it but will probably have a pro do it for me. From the shop manual: 1. PLACE FRONT WHEEL FACING STRAIGHT AHEAD 2. REMOVE COLUMN HOLE COVER SILENCER SHEET (See page SR-9) 3. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (See page PS-21) 4. DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY 5. REMOVE FRONT WHEEL 6. REMOVE ENGINE UNDER COVER LH 7. REMOVE ENGINE UNDER COVER RH 8. REMOVE FRONT STABILIZER LINK ASSEMBLY LH (a) Remove the 2 nuts and front stabilizer link LH. HINT: Use a 6 mm hexagon wrench to hold the stud if the ball joint turns together with the nut. 9. REMOVE FRONT STABILIZER LINK ASSEMBLY RH HINT: Use the same procedures described for the LH side. 10. DISCONNECT TIE ROD END SUB-ASSEMBLY LH (See page DS-6) 11. DISCONNECT TIE ROD END SUB-ASSEMBLY RH (See page PS-21) 12. DISCONNECT PRESSURE FEED TUBE ASSEMBLY (See page PS-21) 13. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH (See page SP-22) 14. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH HINT: Use the same procedures described for the LH side. 15. REMOVE FRONT FLOOR PANEL BRACE (See page EX-2) 16. REMOVE CENTER EXHAUST PIPE ASSEMBLY (See page EX-2) 17. REMOVE HOOD SUB-ASSEMBLY 18. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY 19. SUSPEND ENGINE ASSEMBLY (See page MX-19) 20. REMOVE NO. 1 HOOK (See page PS-22) 21. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (See page PS-22) 22. REMOVE FRONT NO. 1 STABILIZER BRACKET LH (a) Remove the 2 bolts and front No. 1 stabilizer bracket LH from the suspension crossmember. 23. REMOVE FRONT NO. 1 STABILIZER BRACKET RH HINT: Use the same procedures described for the LH side. 24. REMOVE FRONT NO. 1 STABILIZER BAR BUSH (a) Remove the 2 No. 1 stabilizer bar bushes from the stabilizer bar. 25. REMOVE FRONT STABILIZER BAR
You can download the manual online for about $15. Well worth it.

Jun 30, 2009 | Scion TC Cars & Trucks

1 Answer

How to remove trim piece around radio in Scion XA?


http://www.installer.com/pdf/99-8209.pdf

Jun 06, 2009 | 2005 Scion xA

Not finding what you are looking for?
2006 Scion tC Logo

Related Topics:

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scion Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Brad Brown

Level 3 Expert

13732 Answers

Are you a Scion Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...