Question about 2003 Jeep Liberty

2 Answers

Broken screw thermostat

Hi .I have a jeep liberty 2003 .I tried to remove the thermostat .I did , but bottom screw was broken . how can I or someone take it out ?

Posted by on

  • Anonymous Mar 21, 2014

    trying to taking off valve cover on driver side and there is a bolt on the front of the car that I am not sure how to get off

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have tried four hours to drill out broken bolt from thermostat on my jeep liberty this is not working,does anyone have any other suggestions i can try?

Posted on Nov 19, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

If you can remove the thermostat housing and the bottom bolt is visible, you can use a vise grip to remove it.
If the bolt is broken even with the block, then you have to drill it out.

Posted on Oct 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2003 keep liberty. I'm looking for the thermostat. Is it on the upper or lower radiator hose?


3.7L (they had 3 engines)
the hose that goes to a flange with 2 screws. (holding stat)




25443677-rfzsrgdtqaicmpcrwkc1npqq-1-0.jpg

Feb 17, 2015 | 2003 Jeep Liberty

3 Answers

How do i change a thermostat ona 2004 jeep liberty with a 3.7 engine


Disconnect neg batt cable, drain cooling system, loosen lug nuts passenger side, jack up Jeep and use jack stands, remove flap inside wheel well, remove lower radiator hose at engine, remove thermostat cover and take out thermostat and replace.12_29_2011_3_18_38_pm.jpg

Dec 29, 2011 | 2004 Jeep Liberty

2 Answers

Where is the thermostat located on a 2005 jeep liberty 3.7


zjlimited_550.jpg

Fig. The location of the thermostat and its housing on the 3.7L engine
  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .

Hope this helps (remember to rate thisd answer).

Jan 25, 2011 | 2005 Jeep Liberty

1 Answer

I have a 2003 jeep Liberty (freedom Edition). My blower motor doesn't work. it comes on sometimes intermittently. I tried changing the Blower motor resistor but that wasn't the problem. I changed the...


most likely the blower motor it's self needs to be changed! Instructions below!
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 21, 2010 | 2003 Jeep Liberty

    2 Answers

    My 2003 jeep liberty only blows hot air. Even


    Have you charged the cooling gas recently?

    Mar 02, 2010 | 2003 Jeep Liberty

    1 Answer

    CD player in my 2003 Jeep Liberty not playing CD's


    sometimes the cd player optic eye inside is broken and is not able to read the disks. try another cd player or check the wiring behind it ok?

    Jul 26, 2009 | 2003 Jeep Liberty

    1 Answer

    Break light out


    BRAKE light...open the rear hatch/door and inside the jamb should be a screw(s) to take out...also, look between the bumper and bottom of the tail light housing for a screw or two

    Jun 14, 2009 | 2003 Jeep Liberty

    1 Answer

    2003 V6 Jeep Liberty Limited how do I remove front brake rotor


    Hole with notches is likely a torks screw Looks like an allan key hole with extra splines? they make a bit that fits in there. It's on the flat surface where the wheel mounts right?

    Apr 22, 2009 | 2003 Jeep Liberty

    1 Answer

    2003 Jeep Liberty Power Window Off Track


    its the window regulator. not to bad to change. just a couple of screws to remove the door panel. peel the liner back & remove the 6 10mm bolts and uunhook the electrical connector and the window from the regulator. installation is reverse

    Jan 21, 2009 | 2007 Jeep Liberty Sport

    2 Answers

    Need picture of jeep thermostat


    sorry, thermostat and housing are on bottom radiator hose on 03 jeep liberty with a v6

    Nov 21, 2008 | 2003 Jeep Liberty

    Not finding what you are looking for?
    2003 Jeep Liberty Logo

    Related Topics:

    478 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    70365 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6878 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...