Question about 1992 Chevrolet C1500

1 Answer

Looking for delco 16147075 schematic

Thre are parts burned on pc board, need schematics to find values

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 44 Answers

I am not sure if you can even find this information GM does not want you to know to much about their computer systems. I have ever seen one. Usually you just replace the computer, that one shouldn't cost that much. I don't think you have to have it flash burnt. You should be able to pick one up at a parts store.

Posted on Nov 10, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need wiring diagram or schematic of the primary, secondary, and lighting windings or a weller soldering gun. even arough drawing of the windings that's close would work


You know that's a bit goofy, right? Only the manufacturer would have such information.

If you are serious, you CAN do it. Begin with an accurate Ohmmeter to measure the primary and secondary winding resistances on a new gun (at Sears, say.) To do that, measure the new gun's primary resistance at the plug with the trigger pulled, of course. Remove the gun's soldering tip and measure the resistance of the secondary without the tip and any incandescent bulb in place. (No need to pull the trigger.)

Hopefully you have some of the burned wire from the old gun. Measure the diameters of samples of the burned primary (thin) and secondary (thick) wires with a micrometer. With that information, look up wire gauge information online. You may need 24 gauge and 18 gauge enamel coated wire, for example. Note: a burned wire will no longer have its enamel coating so take that into account when determining the gauge of the "new" wire.

Note the "Ohms/foot" specification for each wire gauge. Divide that number into the resistance values you measured on the new gun (at Sears...). That will indicate the number of feet of each gauge of wire you will need to rewind the core!

Now I'm off to build my own refrigerator... NOT!




Feb 11, 2015 | Cars & Trucks

1 Answer

Need wiring diagram for a Dolby delco system. Radio model #16164325. Cassette player model #16156555. Amplifier model #16147075. Paulawomack29@gmail.com Thank you


Hello. I've been there before. Go to a well known autoparts store and look into a doit your self service manuall and look into the radio-audio section. Good Luck.

May 26, 2014 | Cars & Trucks

2 Answers

Can anyone provide a location where is can find a schematic for the HVAC control dash unit out of a 2005 Buick Park Avene?


There won't be a schematic available for what your asking. Only electrical schematics that show wiring harness (to and from) the A/C controller. So what I suggest you do is go to a "Pick Your Part" type wrecking yard and get a replacement controller from a simalar Buick or Chevorlet model. Should be a couple different models built in '05 that use the same controller

Apr 10, 2014 | 2005 Buick Park Avenue

1 Answer

Delco radio wiring schematic


usually a dealer issue check with the parts department.

Apr 08, 2014 | 1998 Cadillac Seville

1 Answer

Have a short on fuse box and caused wires to burn!


get schematic part stores sell them make sure it has the schematic before you buy it

Jan 10, 2014 | 1993 Nissan Pathfinder

1 Answer

Wiring Schematics


Haynes has manuals with wiring diagrams, colors are indicated. These are available at Auto Valu parts stores. About $20.

Nov 28, 2013 | 1996 Dodge Dakota

1 Answer

How can I test the Radio amp #16147075 in my 1993 Chev C1500? Radio and clock work properly, but there is no sound from speakers.


Check the multi-wire connector to the CDM unit to ensure it's mated securely. If it is, the likely problem is the power amplifiers mounted to the heat sink on the back of the CDM unit...but it could also be the tuner preamp section, the IF section or others. If there is absolutely no sound - no hum, no static, etc., I'd look at the power amplifiers. There are several sources of NOS and remanufactured CDM units on eBay and from other online retailers. Without a schematic of the CDM unit, you'd just be shooting in the dark. Replace it and call it a day. Good luck.

Sep 29, 2013 | 1993 Chevrolet K1500

Not finding what you are looking for?
1992 Chevrolet C1500 Logo

Related Topics:

505 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...