Question about 2006 Toyota Sienna

1 Answer

Brake rotors I'm trying to remove the rear rotor from my 2006 Toyota Sienna AWD. The old brake pad wore down and bit into the rotor, which I'm trying to change. I've released the emergency brake, and removed the caliper and caliper arm, but the rotor, although loose, won't wiggle off. What else do I need to do?

Posted by on

  • Anonymous Mar 25, 2014

    rear brake caliper

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 123 Answers

Are there small retainer clips on the studs still? More than likely its just rust built up on the center hub. Take some sand paper to the center hub, as long as e-brake is released and caliper is off, it will come off. I'm not familar with the toyota sienna's but if they have internal drum e-brakes, I would back off the adjuster if they do.

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

1 Answer

Need to perform rear brake pad change on 2006 Volvo V70 AWD 2,5T wagon


brakes are brakes, push in , turn in, or two piece calipers. remove wheel , remove two bolts that hold caliper in place, remove replace pads if rotors look good if not remove caliper retainer and rotor replace or have resurfaced at local part store with service. if push in piston push in with c-clamp or piston tool, if turn in will be solid on top with slots for tool to turn in turn to right, tool can be gotten at parts store, if two piece take apart and put back then bleed brakes.

Aug 19, 2012 | 2006 Volvo V70

1 Answer

Where to buy brake pads and rotors for 2004 toyota sienna


Brake pads and rotors can be purchased at any auto parts store.

Jul 10, 2010 | 2004 Toyota Sienna

1 Answer

How do i change the brakes and rotors on my 2004


When you say fit properly I assume you mean it's not going back together. Make sure you have the bearings and races installed correctly on the back side and that you are installing the correct rotor on the correct side with the correct bearings. The front and rear bearings look the same but they aren't and if you try putting that rotor on with the front side bearing installed in the rear of the rotor it will never go back together.

Jul 12, 2010 | 2004 Toyota Sienna

1 Answer

I changed the brake pads and rotors. After


did you foll your brake resiviour? it need to be at full level to turn off the lite. its under the hood drivers side firewall fill it good luck CJ. .

Jun 01, 2010 | 2006 Toyota Sienna

2 Answers

Toyota 2001 Sienna brake problem when i press the brake pedal the brakes aren't as strong as the used to be. Even with new brake pads. I have to pump the brake pedal to make them have more power. What...


Check your brake fluid level. if ok, have the system bled as there may be air in the brake system. If your fluid is low, have the brake system checked for leaks. Hopefully this helps!!

Apr 02, 2010 | 2001 Toyota Sienna

1 Answer

Changing the rear disk brakes on a 06 toyota sienna, what is the process?


-Set up jack and properly block front tires.

-Do not set parking break as this may hender removing the rear calipers. Open hood and remove the brake resevoir cap.

-Remove hubcaps if applicable,

-Loosen Lugnuts but do not remove,

-Jack up van,

-Remove tire.

-Caliper should be visible. There are two bolts or hex heads on the back side that can be a pain to remove sometimes.

-Pull the caliper off the rotor, It is recomended to have the rotors turned or replaced. With the old pad still in place, take a c clamp or brake caliper squeezer and compress the caliper

-remove old pad, take note for the reinstall of the new pad.

-reverse the steps. This is a simple break down. Hope it helps

Feb 07, 2010 | 2006 Toyota Sienna

1 Answer

How to replace brake pads & rotors


I have a 2006 Sequoia which should have the similar if not the exact same brake system. Changing the pad is very easy and straight forward. No special wrenth was involved. Easier than sedans since no worry to damage the brake fluid pipe.

Apr 28, 2009 | 2001 Toyota Sienna

2 Answers

Problem changing rear rotors on 95 Toyota Avalon


Just remove the rear rotors, bull the straight off, after removing the caliper bracket. It would be a good idea to spray the small brake shoes with brake cleaner. No need to remove anything other than the rotor.

Mar 05, 2009 | 1995 Toyota Avalon

Not finding what you are looking for?
2006 Toyota Sienna Logo

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...