Question about 1999 Honda Civic

1 Answer

Clutch not working right

The clutch pedal goes all the way to the top and then the car barely goes

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,779 Answers

Check your fluid in the reservoir under the hood, on the firewall, make sure it's not low. If level is ok the pedal should be adjusted, and if that doesn't fix it, U will need a new clutch most likely. Try the fixes in this order, The 1st may do it. Let me know what u find. good luck! countrycurt0

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,2002 cavalier now the clutch pedal goes in to start the vehicle and once the pedal is released all the way car barely moves. i thought the slave or master cylinder could be shot


I would think that the clutch itself is shot. If it was the slave cylinder or the master cylinder, you would not be able to get the car into gear when the engine is running. If it goes into gear fine, but just doesn't want to move....it means your clutch is not griping.

Jun 25, 2015 | Cars & Trucks

2 Answers

88 Bronco 2 4x4 2.9L has air in the hydraulic clutch line. I have been pumping the pedal and bleeding it for hours, including cracking the bleed screw with the pedal depressed. nothing seems to work.


Try to find where the air is entering the clutch line. When you bleed the cylinder you cannot drain the reservoir completely when bleeding. If you do then you'll only pump more air into the system.

Oct 29, 2014 | 1988 Ford Bronco II

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

1999 pontiac sunfire clutch pedal stays down


The hydraulic clutch works much like the brake system, there is a master cylinder with a piston and spring that should keep the pedal up.
You may have to take the clutch master cyl off and inspect the internal parts.

Jul 18, 2012 | Cars & Trucks

2 Answers

Is clutch adjustable? Engine revs,but barely moves


it's not if you have hydraulic system.
check to see if the clutch pedal is firm and has pressure
start your engine, depress the clutch pedal and put it in gear
if it goes in gear easily and the car won't move then you need clutch

Apr 21, 2010 | 1996 Ford Explorer

2 Answers

Clutch pedal has alot of play


adjust the cable.....if its not a cable drivin clutch (probably is) then top off your hydraulic clutch tank.

Oct 07, 2009 | 1994 Toyota Pickup

1 Answer

Clutch bites right at the top of thr pedal and


Yes you need a clutch. Look at spending $400 and up.

Jul 12, 2009 | 1993 Mazda MX-5

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

1 Answer

Clutch Problem with 2001 Ford Explorer Sport


might have a fluid leak it is a hydraulic clutch see if there is fluid at the bottom of the trans bell housing

Apr 14, 2009 | 2001 Ford Explorer Sport

2 Answers

Clutch not working


You will need to replace the clutch cable, it goes from the top of the clutch pedal to the top of the transmission.

Aug 18, 2008 | 1998 Ford Escort

Not finding what you are looking for?
1999 Honda Civic Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...