Question about 1989 Ford F 350

1 Answer

How to change inginition?

Lost keys have new key ingintion looking for install info.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

If you have an original replacement key assembly, then all you have to do is remove the old key assembly, transfer the rear electrical ignition switch to the new key assembly and your done.

no need to transfer or solder any wire. if you have a replacement part which is not an original, then it would be very difficult to trace the wires unless you have a knowledge in voltage testing and using a volt meter.

tnx 4 using fixya,

drcool

Posted on Oct 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 mercury mountaineer lost onnly key.. ignition key code location?


I think if you call the dealership with your vin number they can look it up and program the key for you. Sometimes the older vehicles the info get deleted. Its worth a try.

Jun 07, 2015 | 1997 Mercury Mountaineer

1 Answer

1998 Chevrolet Cavalier Factory Imobilizer (Starts and runs for a few seconds, then dies.)


You must know the resistance value of the old key to make this work, without that info you can't get a new key cut, the resistor was the chip at the base of the key shank. So you are kinda stuck here, the only thing to do is find out if you can buy the VATS module out of the truck the column came from, you module needs to see a proper key resistance signal a certain resistance which was of course the one you lost. Only had one key to the truck?? wow that was a mistake. I lost a key once but luckily it had no anti theft system and a new lock fixed it, after that I have three keys for each of my 4 cars.

Aug 08, 2012 | 1998 Chevrolet Cavalier

1 Answer

How to change the key inginition switch on a 94 chevy caprice


Hi, your ignition switch is mounted to the steering column just below the knee bolster by 2 5/16in bolts. First remove the 2 connectors from the switch, then the bolts. The actuating rod is slid into the side of the switch and extends up the column to the lever of the key barrel. Carefully pull the rod from the side of the switch. Slide the actuating rod into the new switch and bolt it on, then plug in the connectors. I have pasted a picture of the switch below. Please let me know if you have more questions.

11_5_2011_12_11_27_am.jpg

Nov 03, 2011 | 1994 Chevrolet Caprice Classic

1 Answer

After parking and trying to remove the key it will not come out. I have to play with the shift gear untill i am able to comepelety turn the the ingintion of all the way and able to take the key out of the...


the locking unit needs to be removed and looked at by a pro--probly worn--junk yards have replacements-------need a repair manual--mitchell/chilton--bookstore or library

Oct 27, 2011 | 1998 GMC Jimmy

1 Answer

My key is locked in the ignition and won't turn. Have moved the sterring wheel but still can't start vehicle


Toyota trucks are nortorious with ingnition problems,spay some wd-40 in the key hole as best you can and move key up and down in rocking motion and turn wheel back and forth as you do this and hopfuly it will turn. if it dont than get the whole ingintion out and try to buy a new one, Ebay perhaps might have one more reasonable for price.

Mar 11, 2011 | 1999 Toyota Tacoma PreRunner

4 Answers

My key is stuck in the ignition of my 2006 Audi A4 automatic Tdi. The button on the gear lever is stuck in in Park Mode. When i put the gear lever in Drive or Reverse the button pops out. When i put it...


ask at the dealer i think it may only need a new stop light switch but i could be wrong ,how about leaving the car in neutral ,does key come out then as should do but later cars like this it might not work in neutral though

Feb 14, 2011 | 2006 Audi Q7

1 Answer

Ignition switch for diesel engine. Lost key


if u notify dealer with vin number they should be able to cut u a new key --if ur key had a electronic chip in it still would need to notify dealer ----if u want to replace ignition switch the switch runs about $130 if electronic more -then u need to add on the price of installing it $65-75 an hour labor cost-- some not many lock- smiths do automotive ignition keys [non electronic ] from vin number

Feb 25, 2010 | 2004 Volkswagen Touareg

1 Answer

Disable a lock system connected to the ingition key


it can't be done the computer needs this signal to start up alot of different circuits

Jul 13, 2009 | 2003 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...