Question about 1995 Nissan 200SX

1 Answer

Key won't turn

I recently had trouble removing my ignition key. Now I cannot not evn turn it to start the car. This happened just after I rolled the car down my driveway 2 feet, without the key in it, to wax my tires. Now the steering wheel is locked in the turned position and I cannot start the car.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

I just needed to jiggle the steering wheel back and forth while turning the key.

Posted on Oct 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key won't turn


hi there,

Your car has a steering lock that clicks into place when you take the car key out of the ignition. This prevents thieves from being able to steer your car if they hotwire it. Sometimes the wheel is turned to just the right place to keep your key from being able to disengage that steering wheel lock. All you have to do is turn the wheel a little bit in either direction while you turn they key. and your done!

Oct 05, 2008 | 1995 Nissan 200SX

1 Answer

I put the key in the car to a on position to roll up windows however after I rolled the windows up I didn't turn it to off and and remove the key and left for about three hours when I came back to start it...


No ---by leaving the key in the "on/run" position you have effectively left the ignition on and that has flattened the battery and possibly burnt out the coil/s and ignition module. Have the battery recharged and reset the CPU using a code reader and go from there . If you have no spark run the fault codes and if it says coil/s and or ignition module then you know what has happened

Mar 09, 2014 | 2009 Chevrolet HHR

1 Answer

Honda Accord keeps blowing fuse and won't start


Recently we had to put a new fuse in the starter ???????????? What fuse ? location , size . A fuse blowing means a electrical short to ground .

May 29, 2017 | 1998 Honda Accord

2 Answers

How can I get key out which is stuck in ignition of 2008 cobalt. It also won't start


This can happen if the battery is low / dead. To solve, connect a set of jumper cables between the battery in the Cobalt and a running car's battery. Shut off the running car. In the Cobalt, make sure all accessories (lights, radio, fan, etc.) are off. Step on the brake, then move the gear shifter fully into the PARK position. Next, either attempt to start the engine, or turn the key to the OFF position and remove it from the ignition.

I hope this helps & good luck!

Jan 03, 2013 | 2008 Chevrolet Cobalt LS

1 Answer

2005 Blazer key won't turn in the ignition


You may want to try to slightly push / pull your vehicle to take weight / tension off the transmission, which in turn will allow you to turn the steering wheel enough to see if the ignition switch can be turned.

Jun 24, 2017 | 2005 Chevrolet Blazer 4WD

1 Answer

I have a 1998 Ford Windstar. Got in to drive, turned the key to start and 'snap' something seems to have broke within the ignition lock cylinder... all of the accessories are on... the key...


This happened to to me with my ranger. I went and bought in ignition and a junk yard and no problems after that. That way your not out of a lot of money.

Jun 02, 2011 | 1998 Ford Windstar

4 Answers

I have a 96 audi a6 and the key is now stuck in the ignition. Car starts and runs but the key will not come out. Just happened out of the blue...


I would try WD-40, spraying down beside the key with a spray nozzle on the end before I took it to a repair shop or pulled the steering wheel.

Jul 07, 2009 | 1996 Audi A6

1 Answer

Trouble Starting Car


I just recently was troubled with the same problem it can only be fixed by changing the ignition switch. you have to get the key and switch together (dealer only) any GM dealer will be able to help with that then remover the steering wheel and get to work or pay a mechanic to do that for you but it will solve the problem you see there is a small white wire that came apart sucks but that's what happened .

Oct 26, 2008 | 1989 Cadillac Seville

Not finding what you are looking for?
1995 Nissan 200SX Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...