Question about 1995 Toyota Pickup

1 Answer

Toyota hilux clutch replacement

Can i jus pull the box back on cross member or does it need to come out

Posted by on

  • chrisy2330 Oct 06, 2008

    4wd cool had to take box out job is done

  • Toyota Ed May 11, 2010

    2wd or 4wd?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

You've got to pull the trans.

Posted on Oct 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change fuse of Toyota hilux 2015


  • locate fuse box
  • locate broken fuse
  • pull out broken fuse
  • push in new fuse

May 24, 2016 | Toyota Cars & Trucks

1 Answer

Do I have to remove the cross-member underneath the engine sump in order to remove the sump fro the engine?


If it is bolted on, then by all means do. It will make the job easier. I haven't worked on yours. But I have had to pull the transmission or the engine to do this job.

Oct 27, 2015 | 2006 Toyota Hilux 3.0

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

1 Answer

How do you replace the clutch on a 1969 morris minor?


remove the battery lead. remove the drive shaft at the diff flange and remove it from the gear box. undo engine mounts/ cross member at rear of gear box if necessary. undo bell housing bolts around rear of engine. remove gear lever if stick shift . If not remove linkages at gear box Pull gearbox rear wards and lower to the ground . A point of interest here is that when a clutch sudders it is advisable to firstly check all the engine mounts are not soft as this affects the clutch operation especially if you have a cable operated clutch

Jun 20, 2014 | 1969 Morris Minor

1 Answer

Steps to Replacing a Clutch on mitsubishi express


for the full steps then get a workshop manual as there are some details that will be missed . Basically it is Remove the battery terminal. remove the rear drive shaft ( front also if 4wd). Remove the gear lever at the tower bolts on the gear box. Drain the gear box or be prepaired for the gear oil to run out the end of the transmission when you pull the box. . Place a bottle jack under the sump at the rear of the engine . Place a trolley jack under the gear box. undo the rear transmission mount cross member Undo all the bell housing bolts. lower the jack and the trolley jack and pull the gear box back. Undo the bolts holding the pressure plate on the flywheel a bit each at a time as you go around the plate . Remove the plate and the clutch plate ( be aware that the clutch plate will only go back in one way so watch the way the clutch hub was facing. Remove and replace the bearing in the back of the crank shaft. clean up the flywheel face ( good idea for a good non shudder job is to have the flywheel re-machined ) fit the clutch plate the right way and fit the pressure plate . Use a clutch aligner tool as it will be impossible to fit the gear box with out it. Replace the clutch throw out bearing. Now re install using the reverse processes As I said a manual shows it all

Dec 14, 2013 | Cars & Trucks

1 Answer

E30 clutch replacement


Drop the drive shaft, tranny cross member, transmission and bell housing. Remove the clutch pressure plate and disc and get new set. Use a pilot/clutch alignment tool in the crank shaft pilot bearing/bushing to center the disc and put the new pressure plate on and torque it down. Then put the bell housing, transmission, cross member, and drive shaft back in, and your done.

Nov 20, 2013 | BMW X5 Cars & Trucks

1 Answer

How do i drop the trans


Remove the Rear Drive Shaft
Remove the Transfer case if 4x4
Disconnect the Shift
Disconnect the Clutch Secondary
Floor Jack under the Transmission
Remove the Cross Member
Remove Bell House Bolts
Pull straight Back
Lower Down
6 Pressure Plate Bolts
Remove 6 Flywheel Bolts

*(Recommend replacing Rear Main Seal)

Resurface Flywheel
Reassemble

Apr 15, 2013 | 1991 Ford F250

1 Answer

How clutch replacement


disconnect battery, remove starte motor, remove drive shafts, support and remove cross member,remove clutch slave cylinder, remove bellhousing bolts and while suspending transmission remove and lower transmission.//remove preasure plate and clutch. Good idea to replace spigot bearing and throw out bearing while you do job. allow 4-5 hrs for r&r. Refit in reverse order.

Nov 17, 2012 | 1987 Toyota 4Runner

2 Answers

Replacing a clutch in my 1989 honda accord any helpful hints im not a wrench monkey im a girl and could us any helpful advice


I can give you the nutshell version, it takes a lot of umph, You have to pull the tarnny out, that means, disconnect thr drive shaft from the tarnny and let it drop or wire it up so it doesn't get in the way, remove the motor mounts but keep the tranny supported by a lift or a jack. remove the engine bolts, starter, battery cable first, when all bolts are off, cross members gone, linkage removed, clutch line removed, pull the tarnny back, you might need a bar or something to priy it out, pull it back, don't let it fall, keep it on the jack, let the jack down a hair as you go, once it on th eground, floor, pull it out of there, make sure you get the car high enough to work under and get the tranny down and out. Not, pull off the pressure plate, clutch, throwout bearing, remove flywheel, if it is cracked, glazed, rough, shot, have it turned, buy a new clutch, PP and bearing, Make sure you have the right clutch by trying it before you muscle that tranny back in. Bolt on the flywheel, PP, center up the clutch plate with a pin or dowel, bolt on the PP, muscle the tranny up and in, get it tight, bolt it up, hook up the linkage, clutch, drive shaft, anything else you took off, cross members, etc, you should be all set. Hope this helps.

Sep 22, 2010 | Honda Accord Cars & Trucks

1 Answer

Need Directions to Replace clutch in a1993 5spd.toyota 4runnerV6


start off bt taking off your shifter, then disconnect the wires,cables, and the 4x4 linkage, the drop out both drive shafts, support the tranny and transfer case then remove the tranny mount. take out the bolts on the bell housing that go into the motor the pull out the slave cylinder,and the last thing to remove is the cross member that holds up your tranny. after that slide the tranny back about 6 inches tor until it's free from the block and lower it down. after you get it on the ground pull of out clutch fork that is in the bell housing of your tranny, pull the bearing off the shaft that is in the bell housing as well. and last but not least take off the clutch plate ans the clutch disk that is on the fly wheel on your block. and i cant stress this enough be careful when you pull the tranny out and make sure it will not fall on you. so please do it carefully. And take your time.

Mar 26, 2009 | 1993 Toyota 4Runner

Not finding what you are looking for?
1995 Toyota Pickup Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...