Question about 1998 Plymouth Voyager

Open Question

How do I replace crankshaft seal on a 1998 Voyager 3.0 v6

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2926 Answers

SOURCE: How do i replace crankshaft seal on 1993 dodge

The oil pump assembly is mounted on the timing belt end of the engine block with the inner pump rotor indexed and installed on the crankshaft nose. The oil pump case also retains the crankshaft front oil seal and provides oil pan front end closure.Disconnect the negative battery cable. Remove the dipstick.

  1. Raise the vehicle and support safely on jackstands.
Remove the crankshaft balancer and sprocket from the crankshaft.
  1. Drain the engine oil and remove the oil pan from the engine
  2. Remove the oil pick-up from the oil pump case.
  3. Remove the oil pump mounting bolts and remove the pump from the front of the engine. Note the different length bolts and their positions in the pump for installation.
  4. Use a small prytool to pry the old oil seal out of the oil pump case. Make certain not to scratch or damage the oil seal mounting surfaces.

ledsled378_10.jpg

ledsled378_11.jpg
To install:

  1. Clean the gasket mounting surfaces of the pump and engine block.
  2. Prime the pump by soaking its components with fresh oil and turning the rotors or, using petroleum jelly, pack the inside of the oil pump. Using a new gasket, install the oil pump on the engine and torque all bolts to 10 ft. lbs. (13 Nm).
  3. Using the front crankshaft oil seal installer special tool MB998306 or equivalent, install the new oil seal in the oil pump.
  4. Install the balancer and crankshaft sprocket to the end of the crankshaft.
  5. Install the oil pump pick-up and oil pan as described earlier in this section.
  6. Install the timing belt and all related parts.
  7. Lower the vehicle.
  8. Install the dipstick. Fill the engine with the proper amount of oil.

Posted on Dec 04, 2010

Ad
duane_wong
  • 6826 Answers

SOURCE: how to replace Honda front Crankshaft Seal

Have to take off the crankshaft pulley to get at the Crankshaft Seal.

Use a hooked seal remover to dig in and pull the seal out without damaging sealing surfaces.

Posted on Jul 21, 2010

mickha2
  • 145 Answers

SOURCE: how to Replace the crankshaft seal on a 1997 geo tracker

remove belts, pull out crankshaft pilley and then pull put seal

Posted on Aug 15, 2010

  • 28 Answers

SOURCE: to remove the crankshaft nut

LEFTY LOOSEY (COUNTERCLOCKWISE)

Posted on Mar 25, 2011

  • 16599 Answers

SOURCE: replace front oil seal 1998 plymouth voyager

which seal on the engine or transmission front engine oil seal not easy or cheap fix will need to remove accessories and crankshaft pulley ----if transmission than need to remove wheels and c/v axles the following link show how to change oil seals on a voyager https://search.yahoo.com/yhs/search?p=oil+seal+98+voyager&ei=UTF-8&hspart=mozilla&hsimp=yhs-004

Posted on Jul 01, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front oil seal 1998 plymouth voyager


which seal on the engine or transmission front engine oil seal not easy or cheap fix will need to remove accessories and crankshaft pulley ----if transmission than need to remove wheels and c/v axles the following link show how to change oil seals on a voyager https://search.yahoo.com/yhs/search?p=oil+seal+98+voyager&ei=UTF-8&hspart=mozilla&hsimp=yhs-004

Jul 01, 2016 | Plymouth Cars & Trucks

1 Answer

On a 1998 Chrysler Cirrus does the transmission have to be removed for the front seal to be replaced?


No, that would be for the rear crankshaft main seal, if it had to be replaced. The front crankshaft seal will be behind the front crankshaft pulley, usually in the timing belt cover.

May 14, 2015 | Chrysler Cars & Trucks

1 Answer

Front main seal leaking 1998 plymouth voyager 3.0


mitsubishi engine, you have to remove timing belt and crankshaft timing gear to get at the seal
they are known to leak

Sep 12, 2011 | 1998 Plymouth Voyager

2 Answers

92 voyager oil pump replacement.


Remove the engine front cover then drain the engine oil and take out the oil pan. It is under the engine and looks like the bottom of the motor.
Unscrew the oil pump mounting bolts with a wrench and proceed to remove the oil pump itself by pulling it down and out of the engine. Avoid getting any contaminants into the oil pump assembly while removing.
Add fresh oil to the new pump to prime it. Check the alignment on the new oil pump drive with the crankshaft/intermediate crankshaft timing.
  • Step 2 Install the new pump carefully, rotating it back and forth a little to make sure it has full surface contact between the pump and the engine block.
  • Step 3 Hold the pump in its sealed position and put in the pump mounting bolts, tightening them to 15 ft-lb.
  • Step 4 Put the engine oil pan back in and refill the crankcase. Start the engine and check for leaks on the parts you replaced
  • May 21, 2010 | 1992 Plymouth Voyager

    3 Answers

    Oil leak on a 96 plymouth voyager between the oilpan and pulley.3L v6. where is it coming from?


    Oil pan gasket or crank shaft seal its going to be one or the other you just have to get down there and see which one it is.

    Jan 19, 2010 | 1996 Plymouth Voyager

    2 Answers

    Where's the crankshaft position sensor located in 98 plymouth voy


    Guessing it's a 6 cyl, 3.0L, but should be located on transaxle housing above vehicle speed sensor.c937fe4.jpg

    Aug 31, 2009 | 1998 Plymouth Voyager

    1 Answer

    Cam belt and tensioner for voyager


    a professional job will cost $850-$ 900 and that entails new belt . cam shaft seals, crankshaft seals , new idlers , new hydraulic belt tensioner
    cheaper jobs will miss seals and idler pulleys and as a result the new belt life will be halved

    Feb 05, 2018 | 2001 Chrysler Voyager

    Not finding what you are looking for?
    1998 Plymouth Voyager Logo

    Related Topics:

    574 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Plymouth Experts

    Marvin
    Marvin

    Level 3 Expert

    81423 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22359 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Plymouth Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...